Apc PER5T-CH User Manual

Browse online or download User Manual for Computer Accessories Apc PER5T-CH. APC PER5T-CH User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Thank you for selecting APC SurgeArrest! It has been designed
to provide the highest value of protection against spikes and
EMI/RFI noise on electrical lines.
Save these instructions for future reference!
SAFETY PRECAUTIONS
Do not install this device during a lightning storm!
The SurgeArrest is intended for a cool (0-40 °C) and dry
indoor environment with relative humidity of 0-95% non-
condensing. Do not install the SurgeArrest near heaters or
in a hot environment. Do not install the SurgeArrest in an
excessively moist or potentially wet environment, for
example: near bathtub, sinks, pools etc.
The SurgeArrest is intended to supply electric power to
computers, peripheral, and electronic equipment. The
SurgeArrest is rated for 250 VAC, 50/60 Hz, and 10 Amps
maximum.
For best protection against spikes induced by lightning
storms, it is hightly recommended that the SurgeArrest surge
suppressor be grounded to earth.
Figure 1
Product Features
Please refer to Figure 1 for the following information and
instructions.
The Power Cord is designed for a three wire grounded
system.
Each SurgeArrest has a built-in recessed ON/OFF Power
Switch to allow the user to activate electricity to connected
equipment such as computers, printers, terminals etc.
The Protection Working indicator (green) is illuminated
as long as the thermal fuse is intact. If this indicator is
extinguished, the product disconnects from the utility line.
In this case, return this unit to APC for repair or replacement.
The Building Wiring Fault indicator (red) is lit when there
is either no ground circuit, a reversed polarity in the building
wiring, or the neutral circuit is overloaded. If it lights, consult
a qualified electrician to examine the building wiring.
Note: When the SurgeArrest is fully loaded, this indicator
may flicker. This is normal and may not be indicative of a
fault.
Five Safety Outlets are provided for your convenience.
These outlets accept a number of different plugs,
including those in use in Continental Europe (CEE7/7 and
CEE7/16), Australia (AS3112), the United Kingdom
(BSI1363), Japan (JIS 8303), and China (GB2099.1).
Note: The rated current of each plug should be 10A or less.
Telephone Protector/ Network Port Protector
Model Per5T-CH is the only model with a built-in one line
(two wire) telephone protector. A six foot telephone
extension cord is provided.
Model Net5N-CH is the only model with a built-in Network
Port Protector (for 10BaseT, 100BaseT, 100BaseTX,
100BaseT4, 100VG-AnyLAN, & Token Ring interface cards
& HUBs).
Note: Never connect an ISDN line to a SurgeArrest.
Each SurgeArrest is equipped with a 10 Amp circuit breaker
to protect against electrical power overload. Button will pop
up in the event of an overload. If this happens, unplug at
least one piece of equipment, and reset button.
Figure 2
Installation Instructions
1. Turn OFF Power Switch . The switch lever marked with
the “O” should be down.
2. Connect the Power Cord
to a 250VAC receptacle. It is
highly recommended that a grounded receptacle be used.
Please note that ungrounded surge protectors do not provide
effective surge protection between line and ground. Check
local electrical laws governing grounding practices.
3. Connect power cords of electrical equipment to be protected
into the Outlets on the SurgeArrest.
4. For model Per5T-CH, protect your telephone, fax machine,
or modem by connecting the supplied telephone extension
cord to the telephone jack on the wall and connecting the
other end to the jack marked “IN” on the SurgeArrest.
Connect your telephone equipment cord to the jack marked
“OUT” on the SurgeArrest.
Table 2: Telephone Protector Ratings
ledoM/retemaraP Posrelan krowteN
egatloVgnitarepOCDV062—
tnerruCegruSkaeP
)eslupsµ02x8htiw(
sedoMllA
A0054—
seniLforebmuN
detcetorP
1—
epyTrotcennoCJR—
ecnatsiseRseireSW21-6—
11
Table 3: Network Protector Ratings
ledoM/retemaraP lanosreP krowteN
egatloVgnitarepO—CDV8
865AIT/AIE
ecnamrofreP
yrogetaC
5
epyTrotcennoC—54JR
Limited Product Warranty
American Power Conversion offers a limited two year warranty
on SurgeArrest surge suppressors.
APC warrants its products to be free from defects in materials
and workmanship under normal use and service for two years
for the original purchaser. Its obligation under this warranty is
limited to repairing or replacing, at its sole option, any such
defective products. To obtain service under warranty you must
obtain a Returned Material Authorization (RMA) number from
APC or an APC service center with transportation charges
prepaid and must be accompanied by a brief description of the
problem and proof of date of purchase. This warranty applies
only to the original purchaser.
Customer Service/Technical Support
APC China
RM 513 Haowei Building
No. 25 Beitaipingzhuang Road, Haidian District
Beijing, 100088
People’s Republic of China
Phone: 86-10-6201-6688
Fax: 86-10-6201-7658
American Power Conversion
132 Fairgrounds Road
West Kingston, Rhode Island 02892
USA
Internet Address: http://www.apcc.com
Part Number: 990-0070 Rev. 2 5/99
5. For model Net5N-CH, protect your local area network card
by connecting the LAN cable from the Concentrator HUB
to the “IN” jack on the SurgeArrest. Connect one end of the
supplied cable to the network card jack and connect the other
end to the “OUT” jack on the SurgeArrest.
6. Turn ON the SurgeArrest power switch.
7. Turn ON connected equipment.
Note: Installation example is shown in Figure 3.
Figure 3
Mounting the SurgeArrest on a wall
The SurgeArrest has two mounting holes located on the bottom
of the unit. These holes were designed to hook on to screw heads
or nail heads. The spacing between the center of the screw holes
is 11.43 cm. For best results, when fastening screws or nails
into a wall, leave about 3.5 mm spacing between the wall and
the bottom flange of the screw or nail.
Specifications
Unless otherwise stated, ratings are based on ambient
temperature of 20°C.
Operating Temperature Range: 0°C to 40°C
Operating Voltage: 250 VAC (230 VAC nom.), 50/60 Hz
Operating Relative Humidity: 0 - 95% non-condensing
Safety Approval: CCEE
For more a detailed specification, contact APC.
Table 1: AC Surge Performance Ratings
ledoM/retemaraP lanosreP krowteN
esioNIFR/IME
otzHk001(noitcejeR
)zHM01
Bd55-51Bd07-03
edoMlamroNA.taC
egatloVhguorhTteL
eslupVk6fo%
%5.8<%5.1<
yticapaCygrenElatoTJ513J036
tnerruCegruSkaeP
)eslupsµ02x8htiw(
edoMlamroN
Ak5.5Ak11
tnerruCegruSkaeP
)eslupsµ02x8htiw(
edoMnommoC
Ak11Ak22
Eng_updated_merlin.p65 99-5-27, 16:341
Page view 0
1 2

Summary of Contents

Page 1 - Figure 3

Thank you for selecting APC SurgeArrest! It has been designedto provide the highest value of protection against spikes andEMI/RFI noise on electrical

Page 2 - SurgeArrest

APC SurgeArrest SurgeArrest 0 °C 40 °C 0-95% SurgeArrest SurgeArrestSurgeArrest SurgeArrest 250 VAC 50/60Hz 10 Amps SurgeArrest 1 1➀➁ S

Comments to this Manuals

No comments