Apc AP9608 User Manual

Call-UPS IIAP9208AP9608

64 Secure the Call-UPS II with the screws removed in step 2.5 Turn on the UPS and the protected equipment.External VersionIt is not necessary to turn

73.5 Configure Call-UPS IICall-UPS II requires on-site configuration before remote operation. Youwill be able to change any of the settings later by t

8Note the top line, which displays the model number of the UPS that iscurrently connected . Site ID and Location are user configuration items.The disp

9Any changes to Call-UPS II communication settings are held until the endof the session. Changes are made when Call-UPS II issues modem com-mands at t

10SmartSlot ConfigurationExternal Configuration

114 Operation4-1 Logging On to Call-UPS IIFor on-site logging on to Call-UPS II, see Section 3.5.For remote logging on to Call-UPS II, connect via mod

12first item is “UPS Status and Diagnostics.” Refer to the appropriatesections and accompanying tables that follow.With Smart-UPS and Matrix-UPSType 1

13UPS STATUS (Smart-UPS and Matrix-UPS)Item DescriptionUtility LineUtility line input, in volts AC RMS.UPS OutputUPS output to the load, in volts AC R

14The following fault conditions display only when Call-UPS II is used witha Matrix-UPS and a fault condition exists.• Runtime Calibration• Waiting to

15The following table describes the items on the UPS Status and Diagnos-tics screen when Call-UPS II is used with a Symmetra Power Array. Thetable con

Thank You !Thank you for selecting this American Power Conversion Call-UPS II remotecontrol accessory. Whether you have the SmartSlot or external vers

16UPS STATUS AND DIAGNOSTICS (Symmetra Power Array, Continued)Item DescriptionLoad Assuming NoRedundancyConnected load as a percentage of the capacity

17The System Status line at the bottom of the UPS Status and Diagnosticsscreen can display the following Symmetra status conditions:• Runtime Calibrat

18If the UPS is powered off during a status request, Call-UPS II respondswith the message:UPS Powered OFFIn addition to providing general status infor

19module serial number, in addition to raw status readings. Normally youwill not need to go to these module status screens unless you need infor-matio

204.3 UPS ControlFor remote control of the connected UPS, go to the Main menu and type 2and press ENTER. Call-UPS II displays the Control menu.Select

21If the UPS is powered off when UPS Control is selected from the Mainmenu, Call-UPS II responds with an abbreviated control menu:Type 1 to turn the U

224.4 UPS CharacteristicsUPS characteristics are set at the factory for normal operation and usuallydo not need to be changed. However if a change is

23You can choose a numbered item to change its current setting. Type itscorresponding number and press ENTER. Press SPACEBAR whenprompted to cycle thr

24UPS CHARACTERISTICS (Smart-UPS and Matrix UPS, Cont.)Setting DescriptionSensitivitySensitivity of the UPS to power line fluctuation. Set thisvalue a

25With Symmetra Power ArrayCall-UPS II connected to a Symmetra Power Array displays the followingUPS Characteristics menu:----------------------------

iContents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Overview 11.2 Hardware Requirements 12 Product Description . . . . . .

26UPS CHARACTERISTICS (Symmetra Power Array)Setting DescriptionOutputOutput voltage of the UPS, in volts AC.Output FreqRangeOutput frequency range of

274.5 Data/Event LoggingTo enable logging and to specify which data and events are included inlogging, select 4 from the Main menu. Select items from

28DATA/EVENT LOGGINGItem Default DescriptionPowerEventsONCall-UPS II will log power events, such as utilityline failure and battery exhausted, when en

29The top section of the Call-UPS Setup menu displays the followingCall-UPS II device information which will be needed in case technicalsupport is req

30CALL-UPS II SETTINGSSetting Default DescriptionSet Date– Current date in mm/dd/yy format.Set Time–Current time in hh:mm:ss format. Call-UPS II uses2

31CALL-UPS II SETTINGS (Continued)Setting Default DescriptionAnswerRing0Number of rings before the Call-UPS II modemanswers a call. After each communi

32The initial AT comes from Call-UPS II. Do not include it in the DialString. In this example, the Dial String is DT9,5551212@. DT instructsthe modem

33----------------------- PAGING SETUP ------------------------1- Paging: ON2- Dial String 1: DT9,5551212@3- Dial String 2: DT9,5551212@4- Repeat 1: 1

34The remaining fields in the Paging Setup menu define the events thattrigger a page, the pager(s) that will be paged when the event occurs, andthe co

35will page the first pager but not the second, and that the first pager willshow a “5” after the Site ID when it receives the page.Note: The default

ii4.4 UPS Characteristics 22With Smart-UPS and Matrix-UPS 22With Symmetra Power Array 254.5 Data/Event Logging 274.6 Call-UPS Settings 294.7 Pagi

36------------------- MEASURE-UPS STATUS ------------------PROBE 1 PROBE 2TEMP Celsius): 26.67Low Limit: 1- 18.10 5-High Limit: 2- 23.97 6-HUMIDITY (%

37Press ENTER at the > prompt on the Measure-UPS screen to display freshreadings.MEASURE-UPS INFOItem DescriptionTEMPCurrent ambient temperature of

5 Problem Resolution5.1 Troubleshooting ChartTROUBLESHOOTINGProblem Possible Cause SolutionPower light flashesrapidly when unitis first turned on.Inte

39The troubleshooting chart covers many of the problems that might arisewith Call-UPS II. If you have a problem with Call-UPS II, refer to thischart f

40MANAGEMENT PORT PINOUTPin Function1 Unused2 Receive data inpute3 Transmit data output4 RS-232 high5 Ground6 Unused7 Request to send output8 Clear to

416.2 Product SpecificationsElectricalCurrent Draw(Normal Operation):External 45 mAdc typicalPhysicalSize (H × W × D):External 1.33 × 4.25 × 4.5 in. (

42Appendix: Multiple SmartSlot InstallationIf your UPS configuration uses more than one SmartSlot device, youmust install them in the correct order fo

43Symmetra Power ArrayFor installation of multiple SmartSlot devices in the Symmetra PowerArray, refer to the numbering in the figure that follows. No

11 Introduction1.1 OverviewAmerican Power Conversion’s Call-UPS II is a remote UPS managementdevice that allows you to monitor and control your APC UP

Limited WarrantyAmerican Power Conversion (APC) warrants its products to be free from defects inmaterials and workmanship for a period of two years fr

990-0122B Rev. 3 12/97Addresses:American Power Conversion Corporation132 Fairgrounds RoadP. O. Box 278West Kingston, Rhode Island 02892USAAmerican Po

22 Product Description2.1 The Call-UPS II PanelThe SmartSlot Call-UPS II panel contains the management port and thestatus indicator. See the figure be

32.4 UPS Cable [External Version]Use this cable to connect Call-UPS II to an APC Smart-UPS, Matrix-UPS,Symmetra Power Array or other APC smart device

42.6 Status IndicatorThe status indicator shows the following conditions.STATUS LED INDICATIONOff Call-UPS II is off.On Continuously Call-UPS II is on

53 Installation and Setup3.1 HandlingCall-UPS II is sensitive to electrostatic discharge. It is shipped in a con-ductive bag to help dissipate damagin