APC EP Zero ARF Instruction Manual download pdf (Page 3)

differ slightly from the photos. In those instances the written

instructions should be considered as correct.

3. You must take time to build straight, true and strong.

4. You must use an R/C radio system that is in good condition,

a correctly sized engine, and other components as specified

in this instruction manual. All components must be correctly

installed so that the model operates correctly on the ground

and in the air. You must check the operation of the model and

all components before every flight.

5. If you are not an experienced pilot or have not flown

this type of model before, we recommend that you get the

assistance of an experienced pilot in your R/C club for

your first flights. If you’re not a member of a club, your local

hobby shop has information about clubs in your area whose

membership includes experienced pilots.

6. While this kit has been flight tested to exceed normal use,

if the plane will be used for extremely high stress flying, such

as racing, or if a motor larger than one in the recommended

range is used, the modeler is responsible for taking steps to

reinforce the high stress points and/or substituting hardware

more suitable for the increased stress.

7. WARNING: The cowl, wheel pants, and some fairings are

made of fiberglass, the fibers of which may cause eye, skin

and respiratory tract irritation. Never blow into or on a part

to remove fiberglass dust, as the dust will blow back into

your eyes. Always wear safety goggles, a particle mask and

rubber gloves when grinding, drilling and sanding fiberglass

parts. Vacuum the parts and the work area thoroughly after

working with fiberglass parts.

We, as the kit manufacturer, provide you with a top quality,

thoroughly tested kit and instructions, but ultimately the

quality and ﬂ yability of your ﬁ nished model depends

on how you build it; therefore, we cannot in any way

guarantee the performance of your completed model,

and no representations are expressed or implied as to the

performance or safety of your completed model.

Remember: Take your time and follow the instructions to

end up with a well-built model that is straight and true.

ITEMS REQUIRED

Radio Equipment

A 4-channel minimum radio system is required to fly this

model. We recommend using a 6-channel radio so that wing

flaps can be used.

❏

Futaba

R617FS 7-channel 2.4GHz Receiver

❏

Futaba R114F FM Micro Receiver

(Low Band – FUTL0442, High Band – FUTL0443)

❏

Futaba FM Single Conversion Short Crystal

(Low Band – FUTL62**, High Band – FUTL63**)

❏

(2) 12" [300mm] servo extension

(HCAM2711 for Futaba)

No Flaps Option

❏

(1) Y-harness (FUTM4130)

❏

(4) Futaba 3115 Micro Precision Servo (FUTM0415)

❏

(4) minimum 39 oz-in (2.8 kg-cm) Micro Servos

Operable Flaps Option

❏

(2) Y-harness (FUTM4130)

❏

(2) 6" [150mm] servo extension (HCAM2701 for Futaba)

❏

(6) Futaba 3115 Micro Precision Servo (FUTM0415)

❏

(6) minimum 39 oz-in (2.8 kg-cm) Micro Servos

Motor, ESC and Propeller

❏

Great Planes RimFire .32 (42-50-800kV) Brushless

Outrunner Motor (GPMG4700)

❏

Great Planes Silver Series 45A Brushless ESC

(GPMM1840)

❏

APC 12x8 Electric Propeller (APCQ4133)

Battery and Charger

Other battery packs will also work in this model, but please

be sure to always use a 4S LiPo pack that can supply at least

45A continuous.

❏

FlightPower

EON-X

™

4350mAh 14.8V 30C LiPo

(FPWP6576)

❏

Great Planes ElectriFly Triton

™

EQ AC/DC Charger

(GPMM3155)

LIPO WARNING!!

Read the entire instruction sheet included with the battery.

Failure to follow all instructions could cause permanent

damage to the battery and its surroundings, and cause

bodily harm!

• ONLY use a LiPo approved charger.

• NEVER charge in excess of 4.20V per cell.

• ONLY charge through the “charge” lead. NEVER charge

through the “discharge” lead.

• NEVER charge at currents greater than 1C.

• ALWAYS set charger’s output volts to match battery

volts.

• ALWAYS charge in a ﬁ reproof location.

• NEVER trickle charge.

• NEVER allow battery temperature to exceed 150° F (65° C).

• NEVER disassemble or modify pack wiring in any way

or puncture cells.

• NEVER discharge below 3.0V per cell

• NEVER place on combustible materials or leave

unattended during charge or discharge.

• ALWAYS KEEP OUT OF REACH OF CHILDREN.

1 2 3 4 5 6 7 8 ... 31 32

Comments to this Manuals

No comments

APC EP Zero ARF Instruction Manual Page 3

Comments to this Manuals