APC BE650G User's Guide download pdf

Back-UPS ES 650

User’s Guide

Connect Battery

Equipment

Power On and

Install Software

All other trademarks are property of their respective owners.

Surge Protection

These outlets provide full-time protection from surges even if the

Back-UPS ES is switched OFF. Plug your printer, fax machine,

scanner, or other peripherals that do not need battery power into

these outlets.

Battery Back-up + Surge Protection

These outlets are powered whenever the Back-UPS ES is

switched ON. During a power outage or other utility problems

(brownouts, over-voltages), these outlets will be powered for a

limited time by the Back-UPS ES. Plug your computer,

monitor, CD-ROM drive and two other data-sensitive devices

such as an external disk or tape drive, or Home Phoneline

Networking Association (HPNA) device into these outlets.

Press the ON/OFF switch to power the unit

ON.

A single short beep and the green “Power On”

indicator confirms the Back-UPS ES is on and

ready to provide protection.

The Back-UPS ES should charge for at least 16

hours to ensure sufficient runtime. The unit is

being charged whenever it is connected to utility

power, whether the unit is turned ON or OFF.

If the red Building Wiring Fault indicator (located

on the end near the power cord) is lit, your

building wiring presents a shock hazard that

should be corrected by a qualified electrician.

Install the PowerChute

Personal

Edition

software

Place the PowerChute Personal Edition CD-

ROM into your computer and follow the

installation instructions on the screen.

.apc.com

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

The Back-UPS ES indicates operating status using a combination of visual and audible indicators.

Use the following table to identify the status of the Back-UPS ES.

Status

Visual Indications

(Power On - Green)

(Replace Battery - Red)

Audible Indication Alarm Terminates

When

Power On - UPS is supplying conditioned

utility power to the load.

Power On pushbutton -

ON (lit)

None Not applicable.

On Battery - UPS is supplying battery

power to the load connected to the Battery

outlets.

Power On pushbutton -

ON (off during beep)

Beeping 4 times every

30 seconds

UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning - UPS is supplying

battery power to the load connected to the

battery outlets, and the battery is near

exhaustion.

Replace Battery indicator

is flashing

Rapid beeping (every

1/2 second)

UPS transfers back to

normal operation, or

when UPS is turned off.

Replace Battery - The battery is

disconnected.

The battery is in need of charging, or is at

the end of its usual life and must be

replaced.

Replace Battery indicator

is Flashing

Power On and Replace

Battery indicators -

flashing (alternating)

Constant tone

UPS is turned off with

the power switch.

Overload Shutdown - During On Battery

operation a battery power supplied outlet

overload was detected.

None Constant tone UPS is turned off with

the power switch.

Sleep Mode - During On Battery operation

the battery power has been completely

exhausted and the UPS is waiting for utility

power to return to normal.

None Beeping once every 4

seconds

Utility power is restored,

or if utility power is not

restored within 32

seconds, or the UPS is

turned off.

Building Wiring Fault - Your building

wiring presents a shock hazard that should

be corrected by a licensed electrician.

Building Wiring Fault LED

(red) - ON

None UPS is unplugged, or

UPS is plugged into a

properly wired outlet.

Status Indicators

See the Troubleshooting section for additional assistance.

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe

battery terminal. NOTE: Small sparks may occur during battery connection. This is normal.

Turn the Back-UPS ES over and press in the

release tab. Slide the plastic battery cover

off of the Back-UPS.

Insert the battery back into the compartment.

Slide the plastic battery cover until the release

tab locks into place.

Connect the red battery wire firmly to

the positive (+) battery terminal.

1 2 3

Connect

Connect Modem / Phone / DSL / Fax / 10/100Base-T / HPNA / Cable Modem / CATV

or DSS to Surge Protection

The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line -

DSL), Home Phoneline Networking Association (HPNA) type equipment, modem, 10/100

Base-T Ethernet, or fax machines from surges when connected through the UPS as

shown in the drawing below.

The UPS also protects a cable modem, CATV converter, or DSS receiver from surges

when it is connected through the UPS coaxial connectors as shown in the drawing below.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS ES power cord directly into a wall outlet; not into a surge

protector or power strip.

Connect Computer Cable

The supplied cable and software provide automatic file saving and shutdown of the

operating system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS ES. Connect the other end of the

cable to the USB port on your computer. The software will automatically find the

computer’s USB Port.

BATTERY DOOR

RELEASE TAB

Power On/Off

Switch & Indicator

Replace

Battery

Indicator

NOTE:

Replace Battery Indicator is only visible when illuminated.

Circuit Breaker

Push to Reset

From Wall

Outlet

Dataline outpu to

em, Fax, or

t DSL,

Mod Network

(10/100BASE-T)

Data Port

Cable output to Cable Modem,

CATV converter or DSS input

Cable input from Internet Service

Provider (ISP), CATV or DSS

1 2

Back-UPS ES 650 1
Troubleshooting 2

Summary of Contents

Page 1 - Back-UPS ES 650

Page 2 - Troubleshooting

TroubleshootingUse the table below to solve minor Back-UPS ES installation or operation problems. Consult APC Online Technical Support or call APCTech

Comments to this Manuals

No comments

APC BE650G User's Guide

Browse online or download User's Guide for Uninterruptible power supplies (UPSs) APC BE650G. APC BE650G User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Uninterruptible power supplies (UPSs) APC BE650G