APC GALAXY 990-2258B-001 User Manual download pdf

990-2258B-001

9/2009

*990-2258B-

Installation

MGE™ Galaxy™ 3500

10-40 kVA 380/400/415 V with batteries

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Warning: ALL safety instructions in the Safety Sheet

(990-2940) must be read, understood, and followed when

installing the UPS system. Failure to do so could result in

equipment damage, serious injury, or death.

Warning: After the UPS has been electrically wired, do

not start it up. Start-up is commissioned to authorized

personnel from Schneider Electric.

Caution: All electrical power and power control wiring

must be installed by a qualified electrician, and must comply

with local and national regulations for maximum power

rating.

Note: Ensure that the unit is in its final location prior to

installation.

Note: Battery and utility/mains power must not be

connected until all other wiring has been completed.

See Also: For parallel configurations see manual 990-

3568.

Level the Enclosure

Warning: The system must be installed on a level floor.

The leveling feet will stabilize the enclosure, but will not

account for a badly sloped floor.



Use a 13/14 mm wrench to adjust the four leveling feet.



Ensure that the system is level.

Caution: Do not move the enclosure after the leveling feet

have been lowered.

Floor Anchoring (if applicable)

Anchor the UPS enclosure to the floor

Note: Floor-anchoring bolts are not provided with the UPS.

Purchase the bolts locally (minimum size: M8). Follow the

specifications given by the manufacturer of the floor

anchoring system when bolting the UPS system to the floor.



Reuse the two transport brackets (one

on each side) that were used to secure the

UPS to the pallet during transport.



Drill two to six holes in the floor for

each bracket. Attach with bolts.

Prepare for Cables

Bottom cable entry



From the rear of the UPS, loosen the six

M4 screws from the upper cover (the cable

landing area) on the back and remove.



Route the cables from the

slanted back plate, up

through the punched

bracket, and into the cable

landing area.



Fasten the cables with

cable ties

Note: A conduit box (part no. SUVTOPT001 or

SUVTOPT002) is available as an option.

UPS

XR battery enclosure















1 2 3 4 5 6

Summary of Contents

Page 1 - Installation

990-2258B-0019/2009*990-2258B-InstallationMGE™ Galaxy™ 350010-40 kVA 380/400/415 V with batteriesIMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSW

Page 2 - Dual mains

2Connect the AC Input and AC Output CablesWarning: Use compression type lugs ONLY. Do not loosen or add cables to any factory preinstalled cables on b

Page 3

3EPO wiring – pin connections J108. Connect the EPO cable using one of the following four wiring configurations.Pin connections J106 (UPS). Note: Wh

Page 4 - Specifications

4 Remove the two screws from the cable-inlet at the front and remove the cable-inlet plate. Guide the cable through the hole in the bottom plate and

Page 5 - Minimum breaker settings

5Bypass inputNotes1 Input current based on rated load and batteries fully charged.2 Input current based on full battery recharge, nominal voltage and

Page 6 - Appendix

6Contact InformationFor local, country-specific centers: go to www.apc.com/support/contact.AppendixWiring diagramsDiagram with Maintenance Bypass Pane

Comments to this Manuals

No comments

APC GALAXY 990-2258B-001 User Manual

Browse online or download User Manual for Uninterruptible power supplies (UPSs) APC GALAXY 990-2258B-001. APC GALAXY 990-2258B-001 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Uninterruptible power supplies (UPSs) APC GALAXY 990-2258B-001