APC MGE Galaxy 3500 Specifications download pdf

990-1957A-001

4/2009

*990-1957A-

Installation

MGE™ Galaxy™

3500

10-30 kVA 208/220 V with batteries

IMPORTANT SAFETY INSTRUCTIONS

- SAVE THESE INSTRUCTIONS

Warning: ALL safety instructions in the Safety Sheet

(990-2940) must be read, understood and followed when

installing the UPS system. Failure to do so could result in

equipment damage, serious injury, or death.

Warning: After the UPS has been electrically wired, do

not start it up. Start-up is commissioned to authorized

personnel from Schneider Electric.

Caution: All electrical power and power control wiring

must be installed by a qualified electrician, and must comply

with local and national regulations for maximum power

rating.

Note: Ensure that the unit is in its final location prior to

installation.

Note: Battery and utility power must not be connected until

all other wiring has been completed.

See Also: For parallel configurations see manual 990-

3568.

Level the Enclosure

Warning: The system must be installed on a level floor.

The leveling feet will stabilize the enclosure, but will not

account for a badly sloped floor.



Use a 13/14 mm wrench to adjust the four leveling feet.



Ensure that the system is level.

Caution: Do not move the enclosure after the leveling feet

have been lowered.

Floor Anchoring (if applicable)

Anchor the UPS enclosure to the floor

Note: Floor-anchoring bolts are not provided with the UPS.

Purchase the bolts locally (minimum size: M8). Follow the

specifications given by the manufacturer of the floor

anchoring system when bolting the UPS system to the floor.



Reuse the two transport brackets (one

on each side) that were used to secure the

UPS to the pallet during transport.



Drill two to six holes in the floor for

each bracket. Attach with bolts.

Prepare for Cables

Bottom cable entry



From the rear of the UPS, loosen the six

M4 screws from the upper cover (the cable

landing area), and remove. Save the screws

for later use.



Loosen the two M4 screws (one on each

side) from the top part of the conduit box.

Loosen the M4 screws attaching it to the

bottom part (two screws in a 352 mm (13.8

in) enclosure), (three screws in a 523 mm

(20.50 in) enclosure) and remove. Save the

screws for later use.



Loosen the four M4 screws (two on each

side) from the conduit box bottom and

remove. Save the screws for later use.



Punch as many holes as

needed in the marked areas

of the bottom conduit box.



Attach the conduit box

bottom to the enclosure

(reuse the screws from step

.



Attach conduits to the

conduit box.



Run the cables through

the conduits, the bottom of

the conduit box, and up into

the cable landing area.



Attach the conduit box top to the conduit box bottom, and to the

enclosure reusing the screws from step .



Fasten the cables with cable ties.

UPS

XR battery enclosure

















Bypass

Output

Battery

Mains













1 2 3 4 5 6

Summary of Contents

Page 1 - Installation

990-1957A-0014/2009*990-1957A-InstallationMGE™ Galaxy™ 3500 10-30 kVA 208/220 V with batteriesIMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONSW

Page 2 - J106 and J108 pin connections

2Connect the AC Input and AC Output CablesWarning: Use compression type lugs ONLY. Do not loosen or add cables to any factory preinstalled cables on b

Page 3

3EPO wiring – pin connections J108. Connect the EPO cable using one of the following four wiring configurations.Pin connections J106 (UPS). Note: Wh

Page 4 - Specifications

4 Remove the two screws from the cable-inlet at the front and remove the cable-inlet plate. Guide the cable through the hole in the bottom plate and

Page 5 - Contact Information

5Recommended current protectionNote: AC input/output over-current protection and AC input/output disconnect must be provided by the customer.Recommend

Page 6 - Appendix

AppendixWiring diagramsDiagram with Maintenance Bypass PanelDiagram without Maintenance Bypass Panel