APC Power-Saving Back-UPS ES 8 Outlet 700VA 230V BS 1363 Specifications download pdf

Back-UPS

ES 550/700 Operation

Caution

• For safety, the Back-UPS ES is shipped with one battery wire disconnected. Small sparks may occur during battery

connection.

• Do not install the unit in direct sunlight, in excessive heat or humidity, or in contact with fluids.

• Connect the power cord directly to a wall outlet; not a surge protector or power strip. The outlet

must be located near the equipment and easily accessible.

Connect the Battery

Overview

Turn on the Back-UPS

Press the ON/OFF switch to turn the unit ON. A single short beep and the green “Power On” indicator confirms that

Back-UPS ES is on and ready to provide protection. The UPS will automatically perform a self-test when power is

applied to the unit, the green LED will flash during the self-test.

Note: Prior to first use, charge the Back-UPS for at least 16 hours to ensure sufficient runtime. The unit is charging

whenever it is connected to utility power, whether the unit is turned ON or OFF.



Master Outlet—Connect a master device, such as a computer. See

“Using the power-saving outlets” on page 2.



Battery Backup and Surge Protection—These outlets receive

power whenever the unit is ON. During a power outage or other

utility problems (brownouts, over-voltages), these outlets will

receive power from the unit for a limited time. Connect a computer,

monitor, and two other data-sensitive devices into these outlets.

Note that one of these outlets is the Master outlet. See “Using the

power-saving outlets” on page 2.



Controlled Outlets—Connect peripheral devices. See “Using the

power-saving outlets” on page 2.



Surge Protection—These outlets provide full-time protection from

surges even if the unit is OFF, but will only supply power when the

unit is ON. Connect a printer, fax machine, scanner, or other

peripherals that do not need battery power during power outages.

Note that if the power-saving feature is enabled, three of these

outlets are controlled by the Master outlet.



Data Port—Use the supplied RJ45/USB cable to connect the Back-

UPS unit to a computer to install the software. See “Install the

PowerChute® Personal Edition software” on page 2.



Circuit Breaker—Push to re-set the circuit breaker.



Modem/Phone/Fax—Connect a DSL or dial-up modem, phone,

fax machine, or 10/100 Base-T ethernet equipment. Note: Do not

connect the UPS telephone protection ports to both the

telephone and network system cables at the same time.



Wall outlet—Connect the unit to a data line wall outlet.

bu034a

bu035a

bu036a

bu052a

1 2 3 4

Summary of Contents

Page 1 - ES 550/700 Operation

Back-UPS® ES 550/700 Operation Caution• For safety, the Back-UPS ES is shipped with one battery wire disconnected. Small sparks may occur during bat

Page 2 - Status Indicators

Back-UPS ES 550 & 750 2Install the PowerChute® Personal Edition softwareUsing the supplied USB cable, connect the data port of the unit to the USB

Page 3 - Troubleshooting

Back-UPS ES 550 & 750 3TroubleshootingMaster Function Disabled Master Enable LED - OFFNoneProblem Probable Cause SolutionBack-UPS will not turn o

Page 4 - (6.50 in.)

Comments to this Manuals

No comments

APC Power-Saving Back-UPS ES 8 Outlet 700VA 230V BS 1363 Specifications

Browse online or download Specifications for Uninterruptible power supplies (UPSs) APC Power-Saving Back-UPS ES 8 Outlet 700VA 230V BS 1363. APC Power-Saving Back-UPS ES 8 Outlet 700VA 230V BS 1363 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Uninterruptible power supplies (UPSs) APC Power-Saving Back-UPS ES 8 Outlet 700VA 230V BS 1363