APC RBC13 Datasheet

Browse online or download Datasheet for Unknown APC RBC13. APC Replacement Battery Cartridge #13 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
UXBP
Battery Pack
Models: UXBP24, UXBP24L, UXBP48
Do not move the UXBP with its batteries installed. Doing so may
result in damage to the Battery Pack and/or a shock hazard.
Install only factory-authorized batteries in the UXBP. Improper
batteries may result in a hazardous chemical spill and/or a shock
hazard.
3. Presentation
3.1 UXBP front
UXBP Battery Pack
The UXBP contains either two (UXBP24L) or four (UXBP24, UXBP48)
user-replaceable, sealed lead-acid batteries and the associated cables and
connectors.
1. Front panel/Battery door
The front panel of the Battery Pack provides access for battery installation
and replacement. Refer to Section 4 when installing or replacing batteries.
2. Battery internal coupler
These four couplers connect the UXBP’s replaceable internal batteries. See
Section 4.
3. Batteries
The Battery Pack contains either two (UXBP24L) or four (UXBP24,
UXBP48) nominal 12 Vdc sealed lead-acid batteries. Use only factory-
authorized batteries in the UXBP!
3.2 UXBP rear
1. Battery Pack rear panel coupler
Additional UXBP Battery Packs are connected to this coupler. Refer to
Section 4.5 for information on making connections with this coupler.
2. In-line Battery Pack coupler
This coupler connects the Battery Pack to the UPS or to the rear panel
coupler on another matching Battery Pack.
1. Introduction
The UXBP is a large Battery Pack module designed to be used with a
Smart-UPS system to provide a significant increase in on-battery runtime
for your protected equipment.
For complete information on the Smart-UPS system, refer to the Owner’s
Manual that came with your UPS.
Note: If you are installing your Smart-UPS system for the first time, be
sure to read the Smart-UPS Owners Manual first. Set up your
UPS system before installing the UXBP.
2. Safety!
CAUTION!
Use the UXBP only with a UPS that is properly installed according to
the UPS Owner’s Manual and connected only to a two-pole, three-wire
grounding mains receptacle. The receptacle must be connected to
appropriate branch protection (fuse or circuit breaker). Connection to
any other type of receptacle may result in a shock hazard and may
violate local electrical codes.
Avoid installing the UXBP in locations where there is water or
excessive humidity.
Do not allow water or any foreign object to get inside the UXBP. Do
not put objects containing liquid on or near the unit.
To reduce the risk of overheating the UXBP, avoid exposing the unit to
the direct rays of the sun. Avoid installing the unit near heat emitting
appliances such as a room heater or stove.
Installation Instructions
Page view 0
1 2 3 4

Summary of Contents

Page 1 - Battery Pack

UXBPBattery PackModels: UXBP24, UXBP24L, UXBP48• Do not move the UXBP with its batteries installed. Doing so mayresult in damage to the Battery Pack

Page 2 - 4. Installation

4. Installation4.1 Receiving inspectionWhen you remove the UXBP from its shipping container, inspect it fordamage that may have occurred in transit. I

Page 3 - 4.5 Module interconnections

UXBP24LUXBP24 and UXBP48 - If you have a UXBP24 or UXBP48, slide thesecond battery all the way to the rear of the cabinet beside the firstbattery.UXBP

Page 4 - 7. Specifications

5. Storing the Battery PackThe Battery Pack should be stored in a covered location and withits batteries in a fully-charged state (reports 100% capaci

Comments to this Manuals

No comments