APC SU2200RMXL User Manual download pdf (Page 2)

Battery Charge and Run Times

A floppy disk is shipped with each battery pack to configure your Smart-UPS for use with each new battery pack added. Your Smart-UPS needs to be configured

appropriately so that it can better calculate the discharge time. Connect the UPS’ port to a serial port on a PC or workstation running DOS or Windows, by using

the black colored communications cable included. Next, while at the DOS prompt, insert the floppy disk into a drive and change to that drive’s letter (e.g.. A:)

Then type: battpack com[X] [Y], where [X] = 1 or 2 depending on the serial port used, and [Y] = number of battery packs attached to the UPS.

The Smart-UPS XL Supplement contains tables showing both the time required for charging UPS and battery pack batteries for rated protection and typical run

times.

Note: When configuring a Smart-UPS for use with an SU48RMXLBP, remember that one SU48RMXLBP is equivalent to two battery packs of any

other model.

Replacing the Battery

This battery pack has easy to replace hot-swappable batteries. Battery replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS

and loads on for the following procedure. See your dealer or call the number in this manual for information on replacement battery kits.

Note: Please read the cautions in the APC Safety Guide. Save your data before beginning this procedure. Once the battery is disconnected, the loads

are not protected from power outages.

Battery Replacement Procedure - Rack Mount XL Battery Packs

1. Reach into the finger pull and remove the front cover.

2. Use a flat-blade, screwdriver or coin to remove the battery

door screws and open the door.

Warning! Do not force the battery out. This may

damage internal wiring!

3. Disconnect the battery connector by pulling on the white

cord on the side of the battery.

4. Slide the battery out of the battery pack.

5. Remove the foam separator.

6. Repeat steps 3 - 5 for the second battery.

7. Repeat steps 3 - 6 for the two batteries on the other side of

the battery pack.

Note: Be careful removing the batteries - they are

heavy..

8. Slide the new battery into the battery pack.

9. Connect the battery connector

Note: Small sparks at the battery connectors are normal

during connection.

10. Push the battery in as far as it will go. There are stops in

the back to prevent it from going too far.

11. Replace the foam separator.

12. Repeat steps 8 - 10 for the second battery.

13. Repeat steps 8 - 12 for the two batteries on the other side

of the battery pack.

14. Close the battery door, replace the battery compartment

screws, and replace the front cover.

15. Dispose of the old battery properly at an appropriate

recycling facility or return it to the supplier in the packing

material for the new battery. See the new battery

instructions for more information.

Specifications

All Models

Battery Type Valve-regulated, sealed, lead-acid

Typical Battery Life 3 to 6 years, depending on number of discharge

cycles and ambient temperature

Operating Temperature

0 to 40

°C (+32 to +104°F)

Storage Temperature

-15 to 45

°C (+5 to _113°F)

Operating and Storage

Relative Humidity

0 to 95%, non-condensing

Operating Elevation 0 to +3,000 m (0 to +10,000 ft.)

Storage Elevation 0 to +15,000 m (0 to +50,000 ft.)

Size (H x W x D) Tower:

21.6 x 17.0 x 43.9 cm

(8.5 x 6.7 x 17.3 in.)

Rack Mount:

17.8 x 48.3 x 45.7 cm

(7.0 x 19.0 x 18.0 in.)

Weight - net (shipping) 31.3 (33.1) kg

69.0 (73.0) lb.

61.7 (69.4) kg

136.0 (153.0) lb.

Battery Replacement Procedure - Tower XL Battery Packs

1. Grasp the side of the front cover and tilt it out and down.

2. Unhook the bottom of the cover from the chassis and

remove it to expose the battery door

3. Use a flat-blade screwdriver or a coin to remove the two

battery door screws and open the door.

4. Pull the white cord on the front battery connector to remove

the battery connector.

5. Grasp the tab and gently pull the battery out of the battery

pack.

6. Reach into the battery compartment and grasp the white

cord on the other battery connector. Pull firmly to

disconnect the connector and remove the second set of

batteries.

Note: Be careful removing the batteries - they are heavy..

8. Slide the first set of new batteries into the unit. Hold the

connector down below the top of the batteries and toward

the door, otherwise the assembly will not fit. Guide the

connector over the top of the batteries and press firmly to

connect it to the rear connector of the battery compartment.

Note: Small sparks at the battery connectors are normal

during connection.

9. Slide the second set of batteries in, then guide the

connector over the batteries and press firmly to connect it

to the front connector of the battery compartment.

10. Now close the battery door, replace the screws, and

replace the front cover.

11. Dispose of the old battery properly at an appropriate

recycling facility or return it to the supplier in the packing

material for the new battery. See the new battery

instructions for more information.

Service Contacts

North & Latin America Europe

APC APC

132 Fairgrounds Road Ballybritt Business Park

West Kingston, Rhode Island

02892 USA

Galway, Ireland 10800-

702000

1-800-800-4APC/1-401-789-5735 353-91-702020

Internet: http://www.apcc.com

E-Mail:

North America: [email protected]

Latin America: [email protected]

E-Mail:

[email protected]

1 2

Comments to this Manuals

No comments

APC SU2200RMXL User Manual Page 2

Comments to this Manuals

Related products and manuals for Uninterruptible power supplies (UPSs) APC SU2200RMXL