APC AXFA11G User Manual Page 51
- Page / 118
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
IM 01E20C01-01E
6-23
6. PARAMETER DESCRIPTION
Parameter setting sequence
(for automatic multiple ranges switching)
F10: SO1 Function
Select a function
F11: SO2 Function
Select a function
F14: SO1/2 Active Mode
Select whether SO1 and SO2 output is to
be “Closed (On) Act” or “Open (Off) Act”
Function Selection
No Function: Output is stopped (*: other functions may be selected)
Fwd/Rev Ranges: Forward and reverse flow rate measurement
Auto 2 Ranges: Automatic 2-ranges switching
Auto 3 Ranges: Automatic 3-ranges switching
Auto 4 Ranges: Automatic 4-ranges switching
Refer to Table 6.4.1
and set F10 or F11.
Set the spans for the ranges to be used.
No. 1 range No. 2 range
No. 3 range No. 4 range
If “instantaneous flow rate % display (FR)” is selected for
Display Mode and A10: FLOW RATE(%) is selected for
BRAIN communication, the instantaneous flow rate %
and following symbols will be displayed only for multiple
ranges and forward/reverse flow measurement.
Forward No. 1 range : [F1] Reverse No. 1 range : [R1]
Forward No. 2 range : [F2] Reverse No. 2 range : [R2]
Forward No. 3 range : [F3]
Forward No. 4 range : [F4]
F30: Forward
Span 2
Forward No. 2 range
B23: Flow Span
Forward No. 1 range
F31: Forward
Span 3
Forward No. 3 range
F33: Reverse
Span 1
Reverse No. 1 range
F34: Reverse
Span 2
Reverse No. 2 range
F32: Forward
Span 4
Forward No. 4 range
F0607.EPS
10% of No. 1 range
(set using F40)
10% of No. 2 range
(set using F40)
10% of No. 3 range
(set using F40)
Input
100%
No. 1 range
No. 2 range
No. 3 range
No. 4 range
Output
Reverse
Forward
Minimum span % within multiple and
forward/reverse (set using F41)
F0608.EPS
Figure 6.4.1 Multiple Ranges and Hysteresis Widths
NOTE
For more details regarding the setting of hyster-
esis width, refer to the description of setting
parameter for F40: Auto Range Hys and F41:
Bi Direction Hys.
Multiple Ranges Setting 2:
Multiple ranges switching via external
status input
䊏 For both the forward and reverse directions, switch-
ing of up to four ranges can be carried out based on
status input; however, switching between directions
is not possible. Switching between forward and
reverse ranges is carried out automatically only
when the flow direction reverses.
䊏 SI1 and SI2 status input terminals are used for
multiple range switching. For more details, refer to
Table 6.4.2: Multiple Ranges Switching via External
Status Input.
- IM 01E20C01-01E 1
- Contents 2
- CONTENTS 3
- 1. INTRODUCTION 5
- 1.1 Using the Magnetic 6
- Flowmeter Safely 6
- 1.2 Warranty 6
- 1.3 Combination Remote 7
- Flowtubes 7
- 2. HANDLING PRECAUTIONS 8
- 3. INSTALLATION 9
- 2-inch Pipe Mounting 10
- Panel Mounting 10
- 4. WIRING 11
- 4.3 Wiring Ports 12
- IMPORTANT 13
- 4.4 Wiring Connections 14
- Supply Cables 15
- 4.4.4 DC Power Connection 15
- 4.4.5 Grounding 16
- 4. WIRING 17
- Figure 4.4.6 Wiring Diagram 17
- Figure 4.4.7 Wiring Diagram 17
- Figure 4.4.8 Wiring Diagram 17
- BASIC OPERATING PROCEDURES 20
- (3) Display items 21
- (2 seconds or more) 22
- Select “No” 22
- Select “Yes” 22
- 5.2.2 Setting Mode 24
- F0504-2.EPS 25
- F0505-1.EPS 26
- F0506-1.EPS 27
- 6.2 Parameter Lists 29
- 6.3 Parameter List Overview 30
- T0603-2.EPS 31
- 6. PARAMETER DESCRIPTION 32
- T0607-1.EPS 34
- T0607-2.EPS 35
- T0608-2.EPS 36
- T0612.EPS 38
- 6.4 Parameter Description 40
- Setting Function 43
- No execution 43
- No Execution 43
- Execution 43
- Meter factors of flowtube 44
- Flowtube data plate 44
- Converter data plate 44
- F0601.EPS 44
- T0620.EPS 46
- T0621.EPS 47
- T0626.EPS 49
- T0627.EPS 49
- Switching 50
- Parameter setting sequence 51
- F0612.EPS 55
- F0614.EPS 56
- 0.5% 0.5% 58
- 5.6mA(10%) 58
- F0620.EPS 62
- Default setting (Enable) 62
- F0621.EPS 62
- Write protection (Protect) 62
- 6.5 Alarm Functions 63
- 6.5.2 Alarm Selection 64
- T0651.EPS 66
- 7.1 BT200 Basic Operations 68
- T0804.EPS 69
- 7.2 AXFA11 Operation 70
- Using a BT200 70
- 7.3 Parameter Setting 71
- F0707.EPS 72
- F0708.EPS 73
- “FI-1101” to “FI-1201” 74
- F0802.EPS 76
- (Model 275) 77
- 8.2.2 Display 78
- 8.3 Parameters 79
- 8.3.3 Checking for Problems 80
- 8.3.4 Setting Parameters 80
- F0810.EPS 82
- F0814-2.EPS 85
- F0814-3.EPS 86
- AXFA11 : FI-1100 89
- Poll addr 89
- HELP DEL ESC ENTER 89
- F0820-1.EPS 91
- F0820-2.EPS 91
- F0821-1.EPS 92
- Changing Password 93
- 8.3.5 Menu Tree 95
- (continued on next page) 96
- F0823-4.EPS 98
- 9. ACTUAL OPERATION 99
- 100
- F0902-1.EPS 101
- F0902-3.EPS 102
- Now Auto Zero 102
- Executing 102
- 10. MAINTENANCE 103
- 10.2 Setting of Switches 104
- 10.3 Troubleshooting 106
- 10.3.2 Unstable Zero 107
- 10. MAINTENANCE 108
- 11. OUTLINE 109
- Functions 110
- ■ STANDARD PERFORMANCE 111
- ■ NORMAL OPERATING CONDITIONS 112
- ■ ACCESSORIES 113
- ■ MODEL AND SUFFIX CODE 113
- ● Terminal Configuration 114
- ● Terminal Wiring 114
- ■ EXTERNAL DIMENSIONS 115
- Pipe mounting 116
- Surface mounting 116
- ● Dedicated Signal Cable 117
- AXFC-4-L 117
- AXFC-0-L 117
- REVISION RECORD 118
© 2020, manymanuals.com. All rights reserved. | 0.901 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals