Apc 66124 User Manual download pdf (Page 3)

3402231500/AC

The Network Management Teleservice Card (66124) can be hot-

plugged on MGE

Galaxy

7000 UPSs. It is not necessary to

shutdown the UPS, disconnect the load or restart the UPS.

◗ A. Remove the plastic cover of the Minislot.

◗ B. Note the MAC address of the card before inserting it.

◗ C. Connect the PHONE cable.

◗ D. Connect the ETHERNET cable (network already connected).

◗ E. Insert and secure the card with the screws.

◗ Check the ETHERNET port indications.

◗ Wait until the UPS Data LED flashes regularly (approx. two minutes),

indicating that card start-up has terminated correctly.

Once the card has started, proceed as indicated below.

◗

Connect one end of the serial cable to the Service port.

◗

Connect the other end of the cable to the COM (IOIOI) port of a PC.

◗

Run a terminal emulator such as HyperTerminal

with these settings

"Echo typed characters locally" option: disabled

◗

Press the

↵

key.

◗

press the 1 key (Network configuration menu)

◗

Type MGEUPS (or mgeups), then press the

↵

key.

The main configuration menu is displayed

The card is configured by default with this service enabled. No manual

configuration is required.The IP parameters are automatically collected

by the card.

To view the network configuration(from the main configuration

menu):

◗

Press the 2 key (Network configuration), then press the

↵

key.

◗

Press the 1 key(Read Network settings)., then press the

↵

key.

The settings supplied by the server are displayed:

◗

Note the IP address.

◗

Press the

↵

key

◗

Press the 0 key (Exit), then press the

↵

key.

◗

Press the 0 key (Exit), then press the

↵

key.

Manual configuration is required.

To set the network configuration(from the main configuration menu):

◗

Press the 2 key (Network configuration), then press the

↵

key.

◗

Press the 2 key (Modify Network settings), then press the

↵

key.

◗

Follow the instructions and enter the IP parameters:

Wait until "Done" is displayed, indicating that the IP parameters have

been saved.

◗

Press the 0 key (Exit), then press the

↵

key.

◗

Press the 1 key (Reset), then press the

↵

key.

The card restarts with the new IP settings (after approx. two minutes).

To check whether the

Network Management Teleservice Card

operational after installation and IP settings, proceed as follows.

◗ Run a browser

◗ Enter in the address bar:

http://IP address/ (e.g. http://172.16.1.82/)

◗ The home page is displayed:

◗

Set the time by clicking the Time command.

◗

Continue configuration via the sections in the Settings menu.

◗

Install the Network Management Teleservice Card kit using the

present manual.

◗

Fill in the information form (3402228500).

◗

Send the form to your Teleservice centre (by Fax or Internet).

◗

Your centre will activate this service.

◗

You receive an acknowledgement of receipt.

The information form must be sent back in order to trigger remote

monitoring of your equipment.

The manual (34003991EN) provides all the information required to use,

install and configure the

Network Management Teleservice Card

For more information on the supervision, control and configuration

functions offered by the

Network Management Teleservice Card

, see

the user manual on the

www.apc.com

web site.

INSTALLATION

IP SETTINGS

Bits per second Data bits Stop bits Flow control

38400 8 1 none

APC by Schneider Electric

NETWORK MANAGEMENT CARD

1 : Reset

2 : Network configuration

3 : Set Login Password to Default

4 : Return to Default Configuration

0 : Exit

Your network is equipped with a BOOTP/DHCP server (default)

Network configuration :

MAC address : 00:06:23:00:1C:07

Mode : DHCP

IP address : 172.17.23.18

Subnet mask : 255.255.248.0

Gateway : 172.17.17

UPS

(

)

000623001C07

Your network is not equipped with a BOOTP/DHCP server

1 : Read Network settings

2 : Modify Network settings

3 : Set ethernet speed

0 : Exit

For each of the following questions, you can press "Return" to select

the value shown in braces, or you can enter a new value

Should this target obtain IP settings from the network?[N] N

Static IP address [172.17.16.16]?172.16.1.82

Subnet mask IP address [255.255.0.0]? 255.255.255.0

Gateway address IP address [0.0.0.0]? 172.17.17.1

Done

ACCESS TO SUPERVISION

Teleservice procedure

USER MANUAL

1 2 3 4

Comments to this Manuals

No comments

Apc 66124 User Manual Page 3

Comments to this Manuals

Related products and manuals for Hardware Apc 66124