APC AXFA11G User Manual Page 78
- Page / 118
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
IM 01E20C01-01E
8-4
8. OPERATION VIA HART COMMUNICATOR
8.2.2 Display
The HART Communicator automatically searches for the AXFA11 on the 4 to 20 mA loop
when it is turned on. When the HART Communicator is connected to the AXFA11, it
displays the “Online” menu as shown below.
(If AXFA11 is not found, the communicator displays the message “No Device Found.
Press OK....” Press the OK ‘F4’ function key and the main menu appears. Please retry after
confirming the connection with the AXFA11.)
Manufacturer’s Field Device
Type Code
Tag (8 Characters) <1>
<2>
<3>
<4>
<5>
Function keys
appears when the voltage
level of the battery is low
The arrow mark corresponding
to the pressed key appears.
Inverse video bar
AXFA11 :
Online
1 Device Setup
2 PV 0.0m
3
/h
3 PV AO 4.000 mA
4 PV Span 1176.5m
3
/h
SAVE
F0805.EPS
Figure 8.2.2 Display
<1> appears and flashes during communication between the HART Communicator
and the AXFA11. In Burst Mode*, appears.
<2> The current display menu title appears.
<3> Each item in menu <2> appears.
<4> and/or appear when the items are scrolled out of the display.
<5> On any given menu, the label appearing above a function key indicates the function
of that key for the current menu.
* Refer to “8.3.4.7 Burst Mode”.
8.2.3 Calling Up Menu Addresses
The 8.3.5 Menu Tree shows the configuration of the “Online” menu which is needed for
operation with the HART Communicator. The desired item can be displayed with ease by
understanding the menu configuration.
When the HART Commnicator is connected to the AXFA11, the “Online” menu will be
displayed after the power is turned on (see figure 8.2.2). Open the desired item as follows:
Key Operation
There are two ways of selecting the desired menu item.
1. Use the or key to select the desired item, and then press the key.
2. Press the number key displayed for the desired item.
• To return to the previous display, press the key, EXIT (F4), ESC (F3) or ABORT
(F3).
NOTE
Setting parameters on the display unit of the AXFA11 is not possible during
HART Communication.
- IM 01E20C01-01E 1
- Contents 2
- CONTENTS 3
- 1. INTRODUCTION 5
- 1.1 Using the Magnetic 6
- Flowmeter Safely 6
- 1.2 Warranty 6
- 1.3 Combination Remote 7
- Flowtubes 7
- 2. HANDLING PRECAUTIONS 8
- 3. INSTALLATION 9
- 2-inch Pipe Mounting 10
- Panel Mounting 10
- 4. WIRING 11
- 4.3 Wiring Ports 12
- IMPORTANT 13
- 4.4 Wiring Connections 14
- Supply Cables 15
- 4.4.4 DC Power Connection 15
- 4.4.5 Grounding 16
- 4. WIRING 17
- Figure 4.4.6 Wiring Diagram 17
- Figure 4.4.7 Wiring Diagram 17
- Figure 4.4.8 Wiring Diagram 17
- BASIC OPERATING PROCEDURES 20
- (3) Display items 21
- (2 seconds or more) 22
- Select “No” 22
- Select “Yes” 22
- 5.2.2 Setting Mode 24
- F0504-2.EPS 25
- F0505-1.EPS 26
- F0506-1.EPS 27
- 6.2 Parameter Lists 29
- 6.3 Parameter List Overview 30
- T0603-2.EPS 31
- 6. PARAMETER DESCRIPTION 32
- T0607-1.EPS 34
- T0607-2.EPS 35
- T0608-2.EPS 36
- T0612.EPS 38
- 6.4 Parameter Description 40
- Setting Function 43
- No execution 43
- No Execution 43
- Execution 43
- Meter factors of flowtube 44
- Flowtube data plate 44
- Converter data plate 44
- F0601.EPS 44
- T0620.EPS 46
- T0621.EPS 47
- T0626.EPS 49
- T0627.EPS 49
- Switching 50
- Parameter setting sequence 51
- F0612.EPS 55
- F0614.EPS 56
- 0.5% 0.5% 58
- 5.6mA(10%) 58
- F0620.EPS 62
- Default setting (Enable) 62
- F0621.EPS 62
- Write protection (Protect) 62
- 6.5 Alarm Functions 63
- 6.5.2 Alarm Selection 64
- T0651.EPS 66
- 7.1 BT200 Basic Operations 68
- T0804.EPS 69
- 7.2 AXFA11 Operation 70
- Using a BT200 70
- 7.3 Parameter Setting 71
- F0707.EPS 72
- F0708.EPS 73
- “FI-1101” to “FI-1201” 74
- F0802.EPS 76
- (Model 275) 77
- 8.2.2 Display 78
- 8.3 Parameters 79
- 8.3.3 Checking for Problems 80
- 8.3.4 Setting Parameters 80
- F0810.EPS 82
- F0814-2.EPS 85
- F0814-3.EPS 86
- AXFA11 : FI-1100 89
- Poll addr 89
- HELP DEL ESC ENTER 89
- F0820-1.EPS 91
- F0820-2.EPS 91
- F0821-1.EPS 92
- Changing Password 93
- 8.3.5 Menu Tree 95
- (continued on next page) 96
- F0823-4.EPS 98
- 9. ACTUAL OPERATION 99
- 100
- F0902-1.EPS 101
- F0902-3.EPS 102
- Now Auto Zero 102
- Executing 102
- 10. MAINTENANCE 103
- 10.2 Setting of Switches 104
- 10.3 Troubleshooting 106
- 10.3.2 Unstable Zero 107
- 10. MAINTENANCE 108
- 11. OUTLINE 109
- Functions 110
- ■ STANDARD PERFORMANCE 111
- ■ NORMAL OPERATING CONDITIONS 112
- ■ ACCESSORIES 113
- ■ MODEL AND SUFFIX CODE 113
- ● Terminal Configuration 114
- ● Terminal Wiring 114
- ■ EXTERNAL DIMENSIONS 115
- Pipe mounting 116
- Surface mounting 116
- ● Dedicated Signal Cable 117
- AXFC-4-L 117
- AXFC-0-L 117
- REVISION RECORD 118
© 2020, manymanuals.com. All rights reserved. | 5.633 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals