APC ACRD500 Installation Manual Page 43
- Page / 60
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
35InRow RD Operation and Maintenance
2. If autorun is enabled, the user interface of the CD starts when you insert the CD. If autorun is not
enabled, open the file contents.htm on the CD.
3. Select the Device IP Configuration Wizard from the main menu.
4. When the Wizard discovers the unconfigured Network Management Card, follow the on-screen
instructions.
Note: If you leave the Start a Web browser when finished option enabled, you can
use apc for both the user name and password to access the Network Management Card
through your browser.
.ini file utility
You can use the .ini file export utility to export .ini file settings from configured Network Management
Cards to one or more unconfigured Network Management Cards. The utility and documentation are
included on the Utility CD.
BOOTP & DHCP configuration
The default TCP/IP configuration setting, BOOTP & DHCP, assumes that a properly configured
BOOTP or DHCP server is available to provide TCP/IP settings to Network Management Cards. The
Network Management Card first attempts to discover a properly configured BOOTP server, and then a
DHCP server. It repeats this pattern until it discovers a BOOTP or DHCP server.
If neither of these servers is available, see “Local access to the control console” on page 36, or
“Remote access to the control console” on page 37 to configure the needed TCP/IP settings
.
A user configuration (.ini) file can function as a BOOTP or DHCP boot file. For more
information, see the TCP/IP configuration section of the User’s Guide, available from the
Utility CD or the APC Web site, www.apc.com.
BOOTP. For the Network Management Card to use a BOOTP server to configure its TCP/IP settings, it
must find a properly configured RFC951-compliant BOOTP server.
1. In the BOOTPTAB file of the BOOTP server, enter the MAC address of the Network
Management Card, and the IP addresses of the subnet mask, and default gateway, and an optional
bootup file name. Look for the MAC address on the display interface (Path: Main > Configure
Network) or on the label on the back of the Network Management Card.
2. When the Network Management Card reboots, the BOOTP server provides it with the TCP/IP
settings.
– If you specified a bootup file name, the Network Management Card attempts to transfer that
file from the BOOTP server using TFTP or FTP. The Network Management Card assumes all
settings specified in the bootup file.
– If you did not specify a bootup file name, you can configure the other settings of the Network
Management Card remotely through its Web interface or control console; user name and
password are both apc, by default.
See your BOOTP server documentation to creat a bootup file.
- Operation and 1
- Maintenance 1
- 동봉된 CD 안에 한국어 매뉴얼이 있습니다 2
- Contents 5
- General Information 9
- Commissioning 11
- Ensure that: 14
- Start-up Inspection Checklist 15
- Final Inspection Checklist 16
- Charging With Refrigerant 17
- Charging the equipment 18
- Compressor Oil Charge 20
- Operation 22
- Using the Display 23
- Time: 13:15:23 24
- Date: 18-Nov-2006 24
- Format: dd/mm/yyyy 24
- Using the Path statement 25
- Password entry 25
- Path: Main > On/Standby 26
- Capacity 27
- Contacts 28
- Cooling Group Configuration 28
- Identify the cooling unit 29
- Configure Modbus 29
- Control the Environment 30
- PID settings 31
- Tune the PID loop 32
- Run hours 33
- Thresholds 33
- Service intervals 33
- Display 34
- Adjust display 35
- Display units 35
- MAC Address 36
- View Status Readings 37
- Cooling group status 38
- About the cooling unit 38
- Path: Main > View Alarms 39
- Path: Main > Clear Alarms 39
- Network Management Card 42
- .ini file utility 43
- Option 43 = 01 04 31 41 50 43 44
- 01) is the code 44
- 04) is the length 44
- Control console 46
- Overview 47
- Web interface 47
- Telnet and SSH 47
- Recover From a Lost Password 50
- Mechanical 52
- Electrical 52
- Functional tests 53
- Cleanliness 53
- Troubleshooting 54
- Warranty 56
- Warranty claims 57
- Warranty Procedures 58
- *990-3234-001* 60
Related products and manuals for Split-system air conditioners APC ACRD500
(24 pages)Hotpoint H8 A2E SB H O3 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Hotpoint H8 A2E SB H O3.
Wir stellen 2 PDF-Handbücher Hotpoint H8 A2E SB H O3 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Gebrauchs- und Pflegeanleitung, Betriebsanweisung
Comments to this Manuals