APC AR1100 Operator's Manual Page 24
- Page / 144
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10
BEFORE USE: Measurement Screen Description
Auto button ( )
Selects the auto-tracking function and auto-shooting function.
Select auto-tracking from 3D, 2D or OFF. Select auto-shooting from ON or OFF.
Min. pupil mark
The concentric circle displayed by eight bright points indicates the minimum measurable pupil size.
If the pupil is smaller than this mark or eyelashes obscure this mark, measurement may not be possible.
Measured values
Displays the latest measured results.
Numeric values displayed to the right of “R: ” and “K: ” are the respective measurement count.
The numeric value in parentheses displayed to the right of “R: ” is a confidence index.
* “P: ” is not displayed when the 43. CONF. INDEX parameter is set to NO.
Mode mark
Indicates the set mode.
The set mode is indicated by the R/K mode mark ( ) and the NT mode mark ( ).
When the two marks are displayed at the same time, the set mode is RKT mode.
Auto-tracking mark
Indicates the setting of the auto-tracking function (alignment in the up, down, left, right, back and forth
directions and focusing in the back and forth direction).
The TONOREF II displays 3D, 2D or Manual (No indication).
Auto-shooting mark
Indicates the setting of the auto-shooting function.
CYL mode
Indicates the selected cylinder mode.
R/K button ( )
Selects a measurement mode in R/K measurement.
Select from AR/KM measurement mode, AR measurement mode or KM measurement mode. The selected
measurement mode is displayed on the screen.
Pressing the button switches the mode in the following order: AR/KM measurement mode (AR and KM continuous
measurements) → AR measurement mode (AR measurement)→ KM measurement mode (KM measurement)→
AR/KM measurement mode......
Auto-tracking in the back-and-forth, side-to-side and up-and-down directions is turned on.
Auto-tracking in the side-to-side and up-and-down directions is turned on.
(No
indication)
Manually align the device and bring the eye into focus.
Measurement starts automatically when the eye is best aligned and focused.
(No
indication)
Press the start button to start measurement.
- OPERATOR 1
- S MANUAL 1
- August 2007 2
- 15601-P902B 2
- Printed in JAPAN 2
- Use precautions 4
- During Use 6
- Wavelength (nm) 8
- After Use 9
- Maintenance 10
- Disposal 10
- { Patient environment 11
- Table of Contents 12
- BEFORE USE 15
- 1.2 Indications for Use 16
- 1.3 Principles 17
- 1.4 Device Description 18
- { Rear view 20
- { Bottom view 22
- 1.5.1 R/K measurement screen 23
- ǁᵃᵆᵋᵆᵐᵅǂ 25
- Parameter button 27
- 1.5.2 NT measurement screen 28
- ÁÖ 29
- [Underside view] 31
- 1.7 Checking Contents 32
- 1.8 Before First Use 33
- 9 Set the printer paper 34
- { Setting by parameter 35
- BEFORE USE: Before First Use 36
- OPERATING PROCEDURES 37
- Turn the power switch on ( ) 38
- 3 Perform checks before use 39
- 5 Prepare the patient 40
- 7 Print the measured results 42
- 㧹㧱㧭㧿㨁㧾㧵㧺㧳ޓ㨃㧵㧺㧰㧻㨃 44
- ޓޓޓޓ㧯㧴㧱㧯㧷㧵㧺㧳 44
- 㨃㧵㧺㧰㧻㨃ޓ㧯㧴㧱㧯㧷ޓ㧻㧷㧍 44
- 2.3.1 Normal shutoff 47
- 2.4 Selecting the Mode 49
- 2.4.2 Sleep mode 52
- Measurements 53
- 4 Measurement starts 57
- 5 Measurement completes 59
- 9 Print the measured results 60
- { CATARACT measurement mode 61
- 2 Measurement completes 64
- KM Measurement Mode 65
- ᴹᵀᵌᵏᵋᵂᴾᵉǽᵐᵆᵗᵂᴻ 67
- ᵐᵑᴾᵏᵑǽᵐᵔǽᴷǽᵀᴾᵍᵑᵒᵏᵂ 67
- PS (Pupil Size) Measurement 69
- ᴹᵍᵒᵍᵆᵉǽᵐᵆᵗᵂᴻ 70
- Manual PD Measurement 71
- to exit from PD mea 72
- Contact lens 73
- ÁÖ 77
- ÁÖ 77
- 8 Start the measurement 80
- 2.6.1 Eyelid detection mode 84
- 2.7 Printing 85
- <Sample printout 2> 86
- 2.7.2 Eyeprint 88
- 2 Press the print button 89
- 2.8 Parameter Settings 90
- { Resetting the parameters 92
- 2.8.1 Parameter tables 93
- [KM (KM measurement)] 94
- [NT (NT measurement)] 94
- [PRINT1 (Print setting 1)] 96
- [PRINT2 (Print setting 2)] 97
- [PRINT3 (Print setting 3)] 99
- 㧞㧠ޓ㧝㧣㧦㧜㧜 103
- 2.8.3 Entering comments 105
- 3.1.1 Outline 107
- 3.1.2 Connecting procedure 108
- 3.1.3 Operating procedure 108
- 3.2.1 Outline 109
- 3.2.2 Connecting procedure 109
- 3.2.3 Operating procedure 110
- 3.3.1 Outline 111
- 3.3.2 Method of connection 111
- 2 Perform measurements 112
- 3 Press the print button 112
- 2 Insert the Eye Care card 113
- MAINTENANCE 115
- 4.3 Replacing Printer Paper 120
- 3 Insert new printer paper 121
- 4.4 Fixing Chinrest Paper 122
- 4.6 Cleaning 125
- 4.6.2 Cleaning the air nozzle 127
- 4.7 List of Replacement Parts 128
- 5.1 Classifications 129
- 5.2 Safety Features 130
- 5.3 Specifications 131
- { Other functions 133
- { Dimensions and weight 133
- { Others 133
- 5.4 Standard Configuration 134
- EMC (IEC 60601-1-2: 2001) 135
- GLOSSARY 139
- GLOSSARY: 140
© 2020, manymanuals.com. All rights reserved. | 4.186 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals