APC Back-UPS ES 350 User Manual download pdf

Safety

Specifications

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!

Connect the Battery” label that covers the outlets. Prior to connecting any equipment

to the unit, connect the battery cable to the unused battery terminal. It is normal for

small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

• Horizontal installation, use 2 screws 5.0" (127 mm) apart.

• Vertical installation, use 2 screws 4.3" (110.4 mm) apart.

• Allow 5/16" (8 mm), of the screw to protrude from the wall.

Connect Equipment

Battery Backup + Surge Protection Outlets

Battery backup outlets provide protection to connected equipment when the

Back-UPS is turned on and connected to utility power.

Battery backup outlets receive power from the Back-UPS for a limited period of time

when a power outage, or brownout condition occurs.

Battery backup outlets provide protection from power surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection Outlets

Surge protection outlets provide protection to connected equipment when the

Back-UPS is connected to utility power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices that do not need to remain on

during power outages, or utility problems to the surge protection outlets.

Connect telephone line

The Back-UPS protects equipment connected to a telephone line from power surges

when connected through the Back-UPS coaxial connectors.

Turn On the Back-UPS

Press the POWER ON button located on the top of the Back-UPS. The Power On/

Replace Battery LED will illuminate and a single short beep will be audible to

indicate that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first 16 hours while connected to

utility power. The Back-UPS battery will charge while the Back-UPS is switched on

or off and is connected to utility power. Do not expect full battery run capability

during the initial charge time.

If the red Building Wiring Fault LED located on the side of the Back-UPS

illuminates, do not operate the Back-UPS. Have a qualified electrician correct the

building wiring fault.

Voltage Sensitivity Adjustment (optional)

The Back-UPS detects and reacts to line voltage distortions by transferring to battery

backup power to protect connected equipment. In situations where either the

Back-UPS or the connected equipment is too sensitive for the input voltage level it is

necessary to adjust the transfer voltage.

1. Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode,

no indicators will be illuminated.

2. Press and hold the ON/OFF button for 10 seconds. The OnLine LED will

illuminate alternately green-amber-red, to indicate that the Back-UPS is in

Program mode.

3. The Power On/Replace Battery LED will flash either green, amber, or red to

indicate the current sensitivity level. Refer to the table for an explanation of the

transfer voltage sensitivity levels.

4. To select LOW sensitivity, press and hold the ON/OFF button until the LED

flashes green.

5. To select MEDIUM sensitivity, press and hold the ON/OFF button until the LED

flashes red.

6. To select HIGH sensitivity, press and hold the ON/OFF button until the LED

flashes amber.

7. To exit Program mode wait five seconds and all LED indicators will extinguish.

Program mode is no longer active.

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in

contact with fluids, or where there is

excessive dust or humidity.

Connect the Back-UPS power cord directly to

a wall outlet. Do not use a surge protector or

an extension cord.

Input

Voltage 120 Vac Nominal

Frequency 60 Hz +

Brownout Transfers 92 Vac Typical

Over-voltage Transfer 139 Vac Typical

Output

UPS Capacity (3 outlets) 350 VA, 200 W

Total Amperage (6

outlets)

8 A (including UPS output)

Voltage - On Battery 115 Vac ± 8%

Frequency - On Battery 60 Hz +

Transfer Time 6 ms Typical, 10 ms maximum

Protection

and

Filtering

AC Surge Protection Full time, 340 Joules

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery

Type Sealed, maintenance-free, lead

acid

Replacement battery cartridge

RBC35

Average Life 3 - 5 years depending on the

number of discharge cycles and

environmental temperature

Physical

Net Weight 9 lb (4 kg)

Dimensions

Length x Width x Height

11 in x 6 in x 3 in

29 cm x 16 cm x 9 cm

Operating Temperature 32º F to 104º F (0º C to 40º C)

Storage Temperature 5º F to 113º F (–15º C to 45º C)

Operating Relative

Humidity

0 to 95% non-condensing

humidity

Operating Elevation 0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC

rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) This

device must accept any interference received, including

interference that may cause undesired operation.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely to

the battery terminal.

 Reinstall the battery compartment

cover. Be sure that the release tab locks

into place.

bu064a

bu065a

bu066a

LED

Flashes

Sensitivity

Setting

Input Voltage Range

(Utility Operation) Recommended Use

Green LOW 88 Vac to 142 Vac Use this setting with equipment that

is less sensitive to fluctuations in

voltage or waveform distortions.

Red MEDIUM 92 Vac to 139 Vac Factory default setting. Use this

setting under normal conditions.

Amber HIGH 96 Vac to 136 Vac Use this setting when connected

equipment is sensitive to voltage

and waveform fluctuations.

bu206a

Back-UPS

Battery Backup +

Surge Protection

bu230a

CAUTION-Refer to bottom

of unit for safety markings.

Circuit

Breaker

Building

Wiring Fault

Te l

Out

Push to

Reset

Te l

User Manual Back-UPS

BE350G Series

1 2

Summary of Contents

Page 1 - BE350G Series

SafetySpecificationsConnect the BatteryThe Back-UPS is shipped with one battery cable disconnected. Remove the “Stop! Connect the Battery” label that

Page 2 - Warranty

Comments to this Manuals

No comments

APC Back-UPS ES 350 User Manual

Browse online or download User Manual for Uninterruptible power supplies (UPSs) APC Back-UPS ES 350. APC Back-UPS ES 350

Summary of Contents

Comments to this Manuals

Related products and manuals for Uninterruptible power supplies (UPSs) APC Back-UPS ES 350