APC MX06 50 User Manual

MX06 50 MX06 100 -48 VDC POWER SYSTEMS User’s Manual (Document # 990-9131B)

MX06 Power Plant User’s Manual Page 6 Ventilation The rectifier modules for this system have fans that provi

MX06 Power Plant User’s Manual Page 7 3.4. Battery Connections WARNING: Hazardous energy levels are pres

MX06 Power Plant User’s Manual Page 8 Figure 3.4-1 Battery Cable Connection Locations Battery LVD Connecti

MX06 Power Plant User’s Manual Page 9 CMNONCYellowYellowBrownOrange1 1 Batt Alm2 2 Brown3

MX06 Power Plant User’s Manual Page 10 Battery Temperature Probe Installation The 15 Ft (4.5m) temperature p

MX06 Power Plant User’s Manual Page 11 3.6. Load Protection Installation Circuit Breaker Installation Stan

MX06 Power Plant User’s Manual Page 12 3.7. Load Connections Cable Size Considerations The DC load cable(

MX06 Power Plant User’s Manual Page 13 GMT Fuse protected Load Connections Connections for ¼ to 15 Amp DC lo

MX06 Power Plant User’s Manual Page 14 RELAY OUTPUT J2 CONNECTOR DESIGNATIONS OUTPUT RELAY NOTES NC 1 MAJOR

MX06 Power Plant User’s Manual Page 15 3.9. Rectifier Module Installation WARNING: Rectifier DC output

MX06 Power Plant User’s Manual Page ii Table of Contents 1 Safety First! 1 1.1. WARNING SYMBOLS ...

MX06 Power Plant User’s Manual Page 16 5) Use a Digital voltmeter to measure the system voltage using the “RT

MX06 Power Plant User’s Manual Page 17 4 Technical Description The various MX06 models are modular stand-alone –48 V dc power plants. Each can be

MX06 Power Plant User’s Manual Page 18 4.2. System Management A single plug-in circuit card provides the con

MX06 Power Plant User’s Manual Page 19 User Inputs t) Temperature Probe: Provides input for battery voltag

MX06 Power Plant User’s Manual Page 20 Battery Low Voltage Disconnect In order to prevent damage to the batt

MX06 Power Plant User’s Manual Page 21 5 Operation 5.1. Description The MX06 is designed for years of operation with no user input. The power sy

MX06 Power Plant User’s Manual Page 22 MX06 External Alarm Input Configuration The MX06-50 and the MX06-100

MX06 Power Plant User’s Manual Page 23 MX06-50 Rectifier Configuration The system Controller Board must know

MX06 Power Plant User’s Manual Page 24 MX06-50 Temperature Probe Selection Temperature compensation can be c

MX06 Power Plant User’s Manual Page 25 MX06-100 Programmable Alarms The GMT alarm, and the battery circuit b

MX06 Power Plant User’s Manual Page iii User Outputs...

MX06 Power Plant User’s Manual Page 26 6 Specifications The overall system specifications can vary, depending upon the number of rectifier modules

MX06 Power Plant User’s Manual Page 27 MX06 100 Power System Nominal Input Voltage 90, 115, 208, 230 VAC In

MX06 Power Plant User’s Manual Page 28 MX06 50 Power System Output Voltage (factory programmed) 54.0 VDC Ope

MX06 Power Plant User’s Manual Page 29 6.3. Controls and Indicators TWF0500H5401 Rectifier FAIL LED DC ou

MX06 Power Plant User’s Manual Page 30 Magnum VS 50 Power System Dimensions 5-1/4 in (13.3 cm) high x 17-1/

MX06 Power Plant User’s Manual Page 31 6.6. Compliance NEBS NEBS Level 3 Safety UL 1950 / CE EMC FCC Part

MX06 Power Plant User’s Manual Page 32 7 APC Worldwide Customer Support Customer Support for this or any other APC product is available at no c

MX06 Power Plant User’s Manual Page 33 8 Limited Product Warranty The limited warranty provided by American Power Conversion Corporation ("AP

MX06 Power Plant User’s Manual Page iv Revision History Revision Date By Preliminary 15 FEB, 2000 SCG PML-

MX06 Power Plant User’s Manual Page 1 1 Safety First! It is very important to follow all safety procedures when unpacking, installing and operatin

MX06 Power Plant User’s Manual Page 2 2 Introduction 2.1. General Information DC Power Plants from APC have

MX06 Power Plant User’s Manual Page 3 ACDCControlACDCControlACDCControlACDCControlACDCControlJ3USERALARMINPUT

MX06 Power Plant User’s Manual Page 4 2.2. How to Use This Manual Each section of this manual can be read i

MX06 Power Plant User’s Manual Page 5 3 Installation 3.1. Unpacking Equipment Remove equipment from packing material and inspect for shipping dam