search

APC UTS6H Specifications Page 27

  • Download
  • Add to my manuals
  • Print
  • Page
    / 68
  • Table of contents
  • TROUBLESHOOTING
    •
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 26
27
freewatt PLUS
• boiler and MCHP unit will produce
condensate at rates up to 2 ½ US quarts per hour.
Make provisions to drain condensate away from both
boiler and MCHP to ensure proper operation. Boiler
is supplied with factory-installed drain trap assembly
with ½” dia. Sch. 40 PVC connection.
Install MCHP condensate line directly into condensate •
pump, located directly behind MCHP unit, if fl oor drain
is not available. Condensate line should have “Y
connector” to ensure tubing is open to atmosphere,
removing chance for air lock in line. Figure 8-10.
Route boiler’s condensate line behind MCHP unit and
install directly into condensate pump.
Supplied boiler condensate vent drain T must be used.•
Do not make any additional electrical connections •
within
freewatt PLUS
System for 120 VAC power.
Separate junction box and receptacle should be
provided if 120 VAC power is required for condensate
pump.
Review installation instructions for boiler and HONDA •
MCHP to ensure a proper installation.
8.11 Onix Clamps
Do not use screw gun or wrench to tighten TorqueTite •
clamps.
Safety glasses must be worn when installing SelfTite •
Clamps.
Minimum bending radius of ½” Onix tubing is 4”.•
Onix requires special Torque-Tite or Self-Tite •
mechanical clamps, designed for higher temperature
and burst pressure ratings.
Self-Tite clamps are supplied with •
freewatt PLUS
System.
TorqueTite clamps are heavy-duty screw-type, •
wide-band, stainless steel clamps. In. per lb. torque
wrench is required to install. Tightened each clamp
according to proper torque setting for size of clamp
used. Torque settings are listed on instruction
sheet supplied with clamps.
Do not over tighten TorqueTite clamp. •
Overtightening may cause long-term damage to
Onix tubing and/or to clamp itself.
SelfTite Clamps are chrome-vanadium, constant •
tension clamps. Watts Radiant recommends using
SqueezeTite pliers to properly open and install clamps.
Do not allow clamp to fl atten while being held open. •
Flattened clamps will not fi t properly over Onix and
barb assembly.
8 - PLACING THE SYSTEM
Figure 8-12 Heat Rejection Connections to HHI
Module (BPHX)
Heat Rejection
OUT
Heat Rejection
IN
Page view 26
1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 67 68

Comments to this Manuals

No comments
Related products and manuals for Network switches APC UTS6H
Network switches APC SYMMETRA 990 Specifications   (4 pages)
Network switches APC Automatic Disconnect Switch User Manual   (36 pages)
Network switches APC AP9258 User Manual   (4 pages)
Network switches APC Automatic Disconnect Switch Specifications   (102 pages)
Network switches APC AP5202 User Manual     (28 pages)
Network switches APC UTS6H Specifications   (40 pages)
Network switches APC MasterSwitch User's Guide   (118 pages)
Network switches APC Automatic TransferSwitch User Manual   (8 pages)
Network switches APC AP5202 Specifications   (28 pages)
Network switches APC UTS6BI User Manual   (24 pages)
Network switches APC SU042-1 3000 VA User Manual   (17 pages)
Network switches APC AP7922 User Manual   (1 pages)
Network switches APC H15 Service Manual   (86 pages)
Network switches APC AP5616 User Manual   (2 pages)
  • Exedy Park-tool Horizon Fotodiox Emberglow
  • Radio Shack Network antennas Philips Men's shavers Alienware Interface hubs Niles Audio Audio tuners NEC Telephones
  • Alpine CDA-9852RB Falmec Prestige Anritsu Site Master S331D Samsung SAMSUNG ES90
  • Samsung 320MX-2 User Manual Danby DFF282SLDB Operations Instructions Jvc RV-NB20 User Manual Canon LEGRIA HF G10 User Manual Multiquip MVH502DSB2 User Manual