Apc SGI 15000 RAID User Manual Page 60
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
46 007-5510-002
RESTART DUAL restarts both units.
RESTART KILL stops a timed restart that is in progress.
3.2.5.2 System Shutdown
SHUTDOWN shuts down the controller unit.
If you need to power down the controller, use SHUTDOWN prior to shutting off power. This will cause
the controller to flush its cache, abort all format and rebuild operations, and proceed with an orderly
shutdown.
All hosts actively using the controller should be safely shutdown and all users logged out before using
this command. The controller will halt all I/O requests and save the data to the disks.
NOTE :
Use SHUTDOWN whenever you power down the controller for maintenance.
SHUTDOWN flushes any data left in the cache and prepares the controller for an orderly
shutdown. For couplet controller configuration, issue SHUTDOWN to both controllers.
To perform a hard restart of the unit by cycling the power, use: SHUTDOWN RESTART=X, where X is
a value between 1 and 1023 seconds before the unit powers up again. If the number is not specified, the
default is 15 seconds.
NOTE :
If SHUTDOWN RESTART is used in conjunction with the DUAL parameter, the
restart will only affect unit where it was issued on and not both.
SHUTDOWN DELAY=X delays a shutdown of a unit between 0 and 255 minutes (where x is minutes
delayed).
SHUTDOWN DUAL shutdowns both units.
SHUTDOWN KILL stops a timed shutdown that is in progress.
3.2.6 Setting the System’s Date and Time
Valid date settings are between years 2000 and 2104. In dual mode, settings should always be done on
Unit 1. Changes will automatically be applied to both units. Settings are automatically adjusted for leap
years.
3.2.6.1 System Date
DATE displays the current system date.
You can also change the system date. At the prompt, type:
date mm dd yyyy
<Enter>
where mm represents the two digit value for month, dd represents the two digit value for day, and yyyy
represents the four digit value for year.
For example, to change the date to March 14, 2009, type:
date 03 14 2009
<Enter>.
- InfiniteStorage 15000 RAID 1
- User’s Guide 1
- COPYRIGHT 2
- Contents 3
- 007-5510-002 i 3
- 007-5510-002 iii 5
- International Standards 7
- Interference 7
- European Regulations 8
- Qualified Personnel 8
- Safe Handling 8
- 007-5510-002 vii 9
- Rack System Precautions 11
- ESD Precautions 12
- Data Security 12
- 007-5510-002 xi 13
- Chapter 1 15
- Introduction 15
- 1.2 The Controller Hardware 16
- Front (behind cover panel) 17
- 4 007-5510-002 18
- 007-5510-002 5 19
- Figure 1–4 Host Port LEDs 20
- 007-5510-002 7 21
- 8 007-5510-002 22
- 007-5510-002 9 23
- Chapter 2 25
- Controller Installation 25
- 2.2 Unpacking the System 26
- Figure 2–1 I/O Connectors 27
- 2.2.6.1 Basic Key Operations 28
- 007-5510-002 15 29
- 2.3.2 Configuration Interface 31
- 2.3.3 Login as Administrator 31
- <Enter> 32
- tier config 33
- 2.3.6.1 Heading Definitions 34
- dual label 35
- 007-5510-002 25 39
- 26 007-5510-002 40
- Chapter 3 43
- Controller Management 43
- Remotely - Telnet 44
- 3.1.3.1 Login 44
- 3.1.3.2 Logout 45
- 3.1.3.3 Password 45
- 3.1.3.4 Who Am I 45
- CLI session: 46
- 15000 [1]: whoami 46
- 3.2.1.2 Host Status 47
- 3.2.1.1 Host ID 47
- Host WWN 47
- 3.2.1.3 Host IB Users 48
- 3.2.1.4 Host Port Speed 48
- Disk and Channel Information 48
- . The tier 49
- 36 007-5510-002 50
- 007-5510-002 37 51
- 3.2.2.1 Tier View 52
- 3.2.2.2 Tier Configuration 53
- 3.2.2.3 LUN View 54
- 3.2.2.4 LUN Configuration 55
- 3.2.2.5 LUN Reservations 55
- 42 007-5510-002 56
- 3.2.4.1 Telnet 57
- 3.2.4.2 SNMP & Syslog 58
- 3.2.5.1 System Restart 59
- 3.2.5.2 System Shutdown 60
- 3.2.6.1 System Date 60
- 3.2.6.2 System Time 61
- 15000 [1]: save 61
- 3.2.9.2 Creating a LUN 62
- 3.2.9.3 Formatting a LUN 63
- 3.2.9.5 Changing a LUN Label 63
- lun label 63
- 3.2.9.7 Deleting a LUN 64
- SCSI Reservations 64
- 3.2.11 SMART Command 65
- 52 007-5510-002 66
- 3.2.12.1 Cache Coherent 67
- Non-Cache Coherent 67
- (Figure 3–28) 68
- 3.3 Performance Management 69
- 3.3.1.1 Cache Segment Size 70
- 3.3.1.3 Prefetch Settings 70
- 3.3.1.4 Cache Settings Reset 71
- Disk Configuration Settings 71
- 58 007-5510-002 72
- 3.3.3 Locking LUN in Cache 73
- 007-5510-002 61 75
- 62 007-5510-002 76
- 100msec intervals 77
- 64 007-5510-002 78
- (Figure 79
- 3.3.4 Resources Allocation 80
- 007-5510-002 67 81
- 68 007-5510-002 82
- 3.3.4.3 Rebuild Journaling 83
- 70 007-5510-002 84
- 15000 [1]: ses m_wait 85
- SES timer m_wait = 6 seconds 85
- 3.3.4.5 Host Command Timeout 86
- 3.4.1 Monitoring User Logins 87
- 3.4.3 User Authentication 88
- 007-5510-002 75 89
- 3.6 Remote Login Management 90
- 15000 [1]: 91
- (Figure 3–57). The 92
- 3.7 System Logs 93
- 80 007-5510-002 94
- 15000 [1]: apc_ups 95
- 15000 [1]: api 95
- 3.8.5 Disk Diagnostics 96
- 3.8.7 SPARE Commands 97
- 84 007-5510-002 98
- Chapter 4 99
- (Figure 4–3) 100
- Troubleshooting 101
- 007-5510-002 87 101
- 88 007-5510-002 102
- 4.1.4.2 Traps 103
- 4.2.1.1 Power Supply Failure 103
- 4.2.1.2 Fan Failure 104
- 007-5510-002 91 105
- 92 007-5510-002 106
- 007-5510-002 93 107
- (Figure 4–7) 108
- Chapter 5 109
- Drive Enclosure System 109
- 5.2 Enclosure Core Product 110
- 5.3 The Plug-in Modules 111
- Table 5–1 PCM LEDs 112
- Figure 5–5 I/O Module 113
- Table 5–2 I/O Module LEDs 113
- 5.3.4 DEM Card 114
- 5.4 Indicators 115
- Table 5–3 Display Panel LEDs 116
- Audible Alarm 116
- 5.4.2 Internal Indicators 118
- 5.6.1 Dimensions 119
- 5.6.2 Weight 120
- 5.6.3 AC INPUT PCM 120
- 5.6.4 DC INPUT PCM 120
- 5.7 Environment 121
- Chapter 6 123
- Drive Enclosure Installation 123
- 110 007-5510-002 124
- 007-5510-002 111 125
- 6.4.1 Controller Options 126
- 6.5 SAS DEM 127
- 6.6 SATA Interposer Features 127
- 6.8 Grounding Checks 127
- Chapter 7 129
- Drive Enclosure Operation 129
- 7.2.2 I/O Panel LEDs 130
- Chapter 8 131
- 8.3 LEDs 132
- 8.3.4 I/O Module 133
- 120 007-5510-002 134
- 8.4 Audible Alarm 135
- 8.5 Troubleshooting 135
- Symptom Cause Action 136
- 8.5.2 Thermal Alarm 137
- 8.5.3 Thermal Shutdown 137
- 8.8 Replacing a Module 138
- 007-5510-002 125 139
- 8.8.2 I/O Module 140
- 8.9 Replacing the DEM 141
- 007-5510-002 143
- Drive Addressing 145
- 007-5510-002 152
Related products and manuals for Tools Apc SGI 15000 RAID
Tools Apc 1400XLT User Manual
(33 pages)
(33 pages)
Tools Apc SU700RM2U User Manual
(2 pages)
(2 pages)
Tools Apc 2000XL User Manual
(44 pages)
(44 pages)
Tools Apc SMARTUPS Smart-UPS 700 User Manual
(60 pages)
(60 pages)
Tools Apc 990-1387A User Manual
(15 pages)
(15 pages)
Tools Apc UPS User Manual
(3 pages)
(3 pages)
Tools Apc SmartSlot Series User Manual
(17 pages)
(17 pages)
Tools Apc 5000VA User Manual
(13 pages)
(13 pages)
Tools Apc 600 User Manual
(44 pages)
(44 pages)
Tools Apc 5000RMB User Manual
(23 pages)
(23 pages)
Tools Apc NETBOTZ NBRK0200 User Manual
(36 pages)
(36 pages)
Tools Apc SILCON 990-4053 User Manual
(76 pages)
(76 pages)
Tools Apc 3000VA User Manual
(25 pages)
(25 pages)
Tools Apc VS 50 User Manual
(65 pages)
(65 pages)
Tools Apc 650 User Manual
(66 pages)
(66 pages)
Tools Apc DP300E User Manual
(38 pages)
(38 pages)
© 2020, manymanuals.com. All rights reserved. | 2.002 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals