Apc SGI 15000 RAID User Manual Page 81
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Controller Management
007-5510-002 67
TIER DELAY=x is used to set the system rebuild/format delay. This value is in 100 millisecond
increments. The range is 0 to 1000. The default setting is 30 milliseconds (3 seconds).
The REBUILD EXTENT parameter determines how much data to rebuild or format at one time. A small
EXTENT value will slow down the rebuild and format operations so they will not affect the performance
of the system. Increasing the EXTENT value will allow more data to be rebuilt in a single pass. The
recommended setting is to use the default value of 32 MBytes (MBs) and only adjust DELAY to match
your user load.
TIER EXTENT=X (where X is a value from 1 to 128) sets the system rebuild/format extent in MBs. The
range is 1 to 128 MBs. Default is 32MBs.
3.3.4.1 Background LUN Verify Operations
LUN VERIFY displays the current setting for background verify on all LUNs.
LUN VERIFY=X turns on background verify for LUN X, where X is a Logical Unit <0..1023>.
LUN VERIFY=ON|OFF prompts you for a list of LUNs where the background verify will be turned either
ON or OFF.
LUN VERIFY=ON will both turn on the background verify for the specified LUN(s), as well as start up
the verify operation(s).
LUN VERIFY=OFF only turns off the Background Verify setting for the specified LUN(s). Therefore,
any Verifys that are already active on the LUN(s) will not terminate until after the completion of that
Verify's current iteration. To stop all verify operations immediately, use the LUN STOP command.
NOTE :
It is recommended that you run LUN VERIFY in continuous mode, since it can help
increase disk reliability.
LUN DELAY= X sets the system Verify Delay value to X, where x is a value from 0 to 1000. The Verify
Delay value determines how long a verify operation will pause after it reaches the verify extent. This
parameter slows down the verify operation so that it will not affect the performance of the system (except
in the case where X is set to 0, as described below).
DELAY=X will remove all delays so that the verify operation will go as fast as possible; however, this
will slow down the performance of the system. This value is in 100 millisecond increments. The range
for X is 0 to 1000. Default is 40.
LUN EXTENT=X sets the system verify extent value X in Mbytes. The verify extent determines how
much data can be verified before the verify operation must pause. This parameter slows down the verify
operation so that it will not affect the performance of the system. Increasing the extent value will allow
more data to be verified in a single pass. The range for X is 1 to 128 MBs. Default is 32 MBs.
3.3.4.2 Background TIER Verify Operations
TIER VERIFY verifies LUNs on a tier by tier basis. TIER VERIFY differs from LUN VERIFY in that the
number of simultaneous Tier Verifys is limited to a value that is set by TIER MAXVERIFIES (default =
2) parameter. The valid range is 1 to 16. If a tier is marked for continuous verification, once the
verification completes, the next sequential tier marked for verification, not presently being verified, will
start.
- InfiniteStorage 15000 RAID 1
- User’s Guide 1
- COPYRIGHT 2
- Contents 3
- 007-5510-002 i 3
- 007-5510-002 iii 5
- International Standards 7
- Interference 7
- European Regulations 8
- Qualified Personnel 8
- Safe Handling 8
- 007-5510-002 vii 9
- Rack System Precautions 11
- ESD Precautions 12
- Data Security 12
- 007-5510-002 xi 13
- Chapter 1 15
- Introduction 15
- 1.2 The Controller Hardware 16
- Front (behind cover panel) 17
- 4 007-5510-002 18
- 007-5510-002 5 19
- Figure 1–4 Host Port LEDs 20
- 007-5510-002 7 21
- 8 007-5510-002 22
- 007-5510-002 9 23
- Chapter 2 25
- Controller Installation 25
- 2.2 Unpacking the System 26
- Figure 2–1 I/O Connectors 27
- 2.2.6.1 Basic Key Operations 28
- 007-5510-002 15 29
- 2.3.2 Configuration Interface 31
- 2.3.3 Login as Administrator 31
- <Enter> 32
- tier config 33
- 2.3.6.1 Heading Definitions 34
- dual label 35
- 007-5510-002 25 39
- 26 007-5510-002 40
- Chapter 3 43
- Controller Management 43
- Remotely - Telnet 44
- 3.1.3.1 Login 44
- 3.1.3.2 Logout 45
- 3.1.3.3 Password 45
- 3.1.3.4 Who Am I 45
- CLI session: 46
- 15000 [1]: whoami 46
- 3.2.1.2 Host Status 47
- 3.2.1.1 Host ID 47
- Host WWN 47
- 3.2.1.3 Host IB Users 48
- 3.2.1.4 Host Port Speed 48
- Disk and Channel Information 48
- . The tier 49
- 36 007-5510-002 50
- 007-5510-002 37 51
- 3.2.2.1 Tier View 52
- 3.2.2.2 Tier Configuration 53
- 3.2.2.3 LUN View 54
- 3.2.2.4 LUN Configuration 55
- 3.2.2.5 LUN Reservations 55
- 42 007-5510-002 56
- 3.2.4.1 Telnet 57
- 3.2.4.2 SNMP & Syslog 58
- 3.2.5.1 System Restart 59
- 3.2.5.2 System Shutdown 60
- 3.2.6.1 System Date 60
- 3.2.6.2 System Time 61
- 15000 [1]: save 61
- 3.2.9.2 Creating a LUN 62
- 3.2.9.3 Formatting a LUN 63
- 3.2.9.5 Changing a LUN Label 63
- lun label 63
- 3.2.9.7 Deleting a LUN 64
- SCSI Reservations 64
- 3.2.11 SMART Command 65
- 52 007-5510-002 66
- 3.2.12.1 Cache Coherent 67
- Non-Cache Coherent 67
- (Figure 3–28) 68
- 3.3 Performance Management 69
- 3.3.1.1 Cache Segment Size 70
- 3.3.1.3 Prefetch Settings 70
- 3.3.1.4 Cache Settings Reset 71
- Disk Configuration Settings 71
- 58 007-5510-002 72
- 3.3.3 Locking LUN in Cache 73
- 007-5510-002 61 75
- 62 007-5510-002 76
- 100msec intervals 77
- 64 007-5510-002 78
- (Figure 79
- 3.3.4 Resources Allocation 80
- 007-5510-002 67 81
- 68 007-5510-002 82
- 3.3.4.3 Rebuild Journaling 83
- 70 007-5510-002 84
- 15000 [1]: ses m_wait 85
- SES timer m_wait = 6 seconds 85
- 3.3.4.5 Host Command Timeout 86
- 3.4.1 Monitoring User Logins 87
- 3.4.3 User Authentication 88
- 007-5510-002 75 89
- 3.6 Remote Login Management 90
- 15000 [1]: 91
- (Figure 3–57). The 92
- 3.7 System Logs 93
- 80 007-5510-002 94
- 15000 [1]: apc_ups 95
- 15000 [1]: api 95
- 3.8.5 Disk Diagnostics 96
- 3.8.7 SPARE Commands 97
- 84 007-5510-002 98
- Chapter 4 99
- (Figure 4–3) 100
- Troubleshooting 101
- 007-5510-002 87 101
- 88 007-5510-002 102
- 4.1.4.2 Traps 103
- 4.2.1.1 Power Supply Failure 103
- 4.2.1.2 Fan Failure 104
- 007-5510-002 91 105
- 92 007-5510-002 106
- 007-5510-002 93 107
- (Figure 4–7) 108
- Chapter 5 109
- Drive Enclosure System 109
- 5.2 Enclosure Core Product 110
- 5.3 The Plug-in Modules 111
- Table 5–1 PCM LEDs 112
- Figure 5–5 I/O Module 113
- Table 5–2 I/O Module LEDs 113
- 5.3.4 DEM Card 114
- 5.4 Indicators 115
- Table 5–3 Display Panel LEDs 116
- Audible Alarm 116
- 5.4.2 Internal Indicators 118
- 5.6.1 Dimensions 119
- 5.6.2 Weight 120
- 5.6.3 AC INPUT PCM 120
- 5.6.4 DC INPUT PCM 120
- 5.7 Environment 121
- Chapter 6 123
- Drive Enclosure Installation 123
- 110 007-5510-002 124
- 007-5510-002 111 125
- 6.4.1 Controller Options 126
- 6.5 SAS DEM 127
- 6.6 SATA Interposer Features 127
- 6.8 Grounding Checks 127
- Chapter 7 129
- Drive Enclosure Operation 129
- 7.2.2 I/O Panel LEDs 130
- Chapter 8 131
- 8.3 LEDs 132
- 8.3.4 I/O Module 133
- 120 007-5510-002 134
- 8.4 Audible Alarm 135
- 8.5 Troubleshooting 135
- Symptom Cause Action 136
- 8.5.2 Thermal Alarm 137
- 8.5.3 Thermal Shutdown 137
- 8.8 Replacing a Module 138
- 007-5510-002 125 139
- 8.8.2 I/O Module 140
- 8.9 Replacing the DEM 141
- 007-5510-002 143
- Drive Addressing 145
- 007-5510-002 152
Related products and manuals for Tools Apc SGI 15000 RAID
Tools Apc 1400XLT User Manual
(33 pages)
(33 pages)
Tools Apc SU700RM2U User Manual
(2 pages)
(2 pages)
Tools Apc 2000XL User Manual
(44 pages)
(44 pages)
Tools Apc SMARTUPS Smart-UPS 700 User Manual
(60 pages)
(60 pages)
Tools Apc 990-1387A User Manual
(15 pages)
(15 pages)
Tools Apc UPS User Manual
(3 pages)
(3 pages)
Tools Apc SmartSlot Series User Manual
(17 pages)
(17 pages)
Tools Apc 5000VA User Manual
(13 pages)
(13 pages)
Tools Apc 600 User Manual
(44 pages)
(44 pages)
Tools Apc 5000RMB User Manual
(23 pages)
(23 pages)
Tools Apc NETBOTZ NBRK0200 User Manual
(36 pages)
(36 pages)
Tools Apc SILCON 990-4053 User Manual
(76 pages)
(76 pages)
Tools Apc 3000VA User Manual
(25 pages)
(25 pages)
Tools Apc VS 50 User Manual
(65 pages)
(65 pages)
Tools Apc 650 User Manual
(66 pages)
(66 pages)
Tools Apc DP300E User Manual
(38 pages)
(38 pages)
© 2020, manymanuals.com. All rights reserved. | 1.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals