APC RAID Subsystem SCSI-SATA II Specifications Page 62
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Subsystem Connection and Operation
4.3.2 Power On Procedure
When powering on the Falcon subsystem, please follow these steps.
1. Power on the JBOD(s) or cascaded subsystem(s).
If any of the subsystems have been connected to a JBOD or cascaded subsystem, the
JBOD or cascaded subsystem must be powered on first. Please refer to the
instruction manual that came with the JBOD to see its own power on procedure.
2. Power on the main subsystem.
The Falcon subsystem should only be powered on after all the JBODs or cascaded
subsystems have been powered on first. The power on procedure for the Falcon
subsystem is described below.
3. Power on the application servers.
The application servers or host computers should be the last devices that are turned
on. Please refer to the instructions that came with your application servers to see
their own power on procedures.
4.3.3 Falcon Power On Procedure
To power on the subsystem, turn on the only power switch located on the rear center of
the subsystem. (See Figure 4-12) The power switch controls all three PSUs. Once it is
switched on, all PSUs will be functional.
Figure 4-12: Falcon Subsystem Power Switch
Power On 4-11
- Falcon 24 Bay 1
- Table of Contents 2
- Safety Precautions 6
- About This Manual 7
- Revision History 7
- Who should read this manual? 7
- Conventions 8
- Software and Firmware Updates 9
- Chapter 1 10
- Introduction 10
- 1.1.2 Enclosure Chassis 11
- 1.1.2.1 Chassis Overview 11
- CAUTION! 12
- 1.1.2.2 Physical Dimensions 12
- 1.1.2.3 Front Panel Overview 13
- 1.1.2.4 Drive Slot Numbering 14
- 1.1.2.5 Rear Panel Overview 14
- 1.2. Subsystem Components 15
- 1.2.2 Drive Trays 16
- WARNING! 16
- 1.2.3 RAID Controller Module 17
- 1.2.5 DIMM Module 18
- 1.2.6 BBU Module 19
- 1.2.7 Power Supply Units 20
- 1.2.8 Cooling Modules 21
- 1.3. Subsystem Monitoring 22
- 1.4. Hot-swappable Components 23
- 1.4.3 Normalized Airflow 24
- Chapter 2 25
- Hardware Installation 25
- 2.3. Static-free Installation 26
- 2.5. Unpacking the Subsystem 28
- Considerations: 29
- WARNING! 30
- 2.7. Hard Drive Installation 34
- 2.8. Drive Tray Installation 35
- Chapter 3 43
- Subsystem Monitoring 43
- 3.2. Status-indicating LEDs 44
- 3.2.2 Controller Module LEDs 45
- 3.2.3 LAN Port LEDs 46
- 3.2.4 LCD Keypad Panel 46
- 3.2.5 Drive Tray LEDs 48
- 3.2.7 PSU Module LED 49
- 3.3. Audible Alarm 50
- C Monitoring 51
- Subsystem Connection and 52
- Operation 52
- 4.1.3 SCSI Termination 53
- 4-5: LCD Keypad Navigation 55
- 4.2 Connection Topology 57
- 4.3 Power On 61
- 4.3.2 Power On Procedure 62
- 4.3.4 Power On Status Check 63
- 4.3.5 LCD Screen 64
- 4.4 Power Off Procedure 65
- Chapter 5 66
- Subsystem Maintenance and 66
- Upgrading 66
- 5.2.1 Overview 68
- CAUTION! 73
- 5.4.2 Replacing a PSU Module 76
- 5.6. Drive Tray Maintenance 79
- 5.6.2 Hard Drive Replacement 80
- Appendix 81
- Subsystem Specifications 81
- A.2.1 Configuration 83
- A.2.2 Architecture 83
- A.6. RAID Management 85
- Appendix B 86
- Uninterruptible Power Supply 86
- B.4.2 Set the Baud Rate 87
- B.4.3 Connect COM2 87
- B.5. Power On 88
- B.6. UPS Status Monitoring 88
- B.6.2 UPS Messages 89
- B.6.3 UPS Message Summary 90
- Appendix C 91
- Spare Parts and Accessories 91
- Appendix D 93
- D.2. DB9 Audio Jack Pinouts 94
- Definitions 95
- D.3. Ethernet Port Pinouts 96
- D.4. Main Power 96
- Index I--1 97
- -2 Index 98
- Index I--3 99
- -4 Index 100
Related products and manuals for Networking APC RAID Subsystem SCSI-SATA II
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.686 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals