APC Automatic Disconnect Switch Specifications Page 53
- Page / 102
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Automatic Transfer Switch with Power Distribution 43
Alarms
View Active Alarms
View a list of all alarms that exist presently. When an alarm is present, the ATS display interface Alarm LED is
red. Choosing this option to View Active Alarms turns the LED off.
Alarm/Event Log
Alarm Setup
View Active Alarms
Alarm/Event Log
Alarm Setup
Alarm Beeper
The following items are available on this menu:
New Logged Items View only alarms and events logged since New Logged Items was last viewed.
When a new alarm is present, the ATS display interface Check Log LED is orange.
Choosing this option, New Logged Items, turns the LED off.
Entire Log View every item in the alarm/event log. When a new alarm is added to the log, the
ATS display interface Check Log LED is orange. Choosing this option, Entire
Log, turns the LED off.
Clear Log Erase all of the items currently in the alarm/event log.
Clr Latched Alarms Erase the latched alarms currently in the alarm/event log. See “Clearing latched
alarms” on page 44 for more information.
Configure the alarm limits (or thresholds) on this menu:
Loading Limits Iout-Alarm Limits:
• Low: If the output current of any phase falls below this value, an alarm condition
exists. The value is set as a percentage of the ATS rating, and also shown in amps.
• High: If the output current of any phase exceeds this value, an alarm condition
exists. The value is set as a percentage of the ATS rating, and also shown in amps.
• Neut: If the output neutral current exceeds this value, an alarm condition exists.
The value is set as a percentage of the ATS rating, and also shown in amps.
Voltage Limits Vout-Alarm Limits:
• Low: If the output voltage of any phase falls below this value, an alarm condition
exists. The value is set as a percentage of the nominal system voltage, and also
shown in volts.
• High: If the output voltage of any phase exceeds this value, an alarm condition
exists. The value is set as a percentage of the nominal system voltage, and also
shown in volts.
- ATS with Power 1
- Distribution 1
- About This Manual 3
- Contents 5
- Overview 11
- Warnings 12
- See also 13
- System Operates 16
- Generator start sequence 17
- Generator cool-down 17
- Source 1 Source 1 Source 2 18
- Source 2 18
- Source 1 Neutral Source 2 18
- ATS with Power Distribution 21
- Front view, door open 22
- ATS panel board, left side 23
- ATS panel board, right side 24
- ATS Component Details 25
- User connection plate 26
- ATS monitoring unit 27
- ATS label kit 28
- Operation 29
- Emergency Manual Operation 32
- /Manual/Auto 36
- Total Power Off 37
- Operation: Total Power Off 38
- Display Interface 39
- NTER key when the selector 40
- Navigating through screens 41
- Password-protected screens 41
- Load-Meter 42
- ATS/Voltage 43
- S2-Generator 44
- ATS Setup 45
- Generator 47
- View Test Log 49
- Run/View Test 49
- Test Schedule 49
- Test Duration 49
- Gen Start: Monthly 50
- Day: 1st Monday 50
- Time: 14:30 50
- Load Test: Monthly 50
- How a test occurs 51
- NTER key and 52
- View Active Alarms 53
- Alarm/Event Log 53
- Alarm Setup 53
- Alarm Beeper 53
- Clearing latched alarms 54
- System/Network 55
- Contacts & Relays 56
- Electrical Config 57
- Factory Defaults 57
- Manufacturer Data 57
- System ID 57
- Communication Configuration 59
- Interface 61
- from the Network menu 66
- Management Interface 67
- Management Interface Password 70
- Relay Outputs to the ATS 71
- NTER key 72
- USER INTERFACE 74
- © 2001 APC 74
- MADE IN USA 74
- EPO Ready To Test 75
- Active Alarm xxofxx 75
- Safety warnings 76
- Circuit Breakers to the ATS 78
- Specifications 85
- Warranty 89
- Life-Support Policy 91
- How to contact APC 92
- Connection 93
- InfraStruXure Generator 94
- Radio Frequency Interference 99
- *990-1845A* 100
Related products and manuals for Network switches APC Automatic Disconnect Switch
Network switches APC AP5202 User Manual
(28 pages)
(28 pages)
Network switches APC UTS6H Specifications
(40 pages)
(40 pages)
Network switches APC MasterSwitch User's Guide
(118 pages)
(118 pages)
Network switches APC AP5202 Specifications
(28 pages)
(28 pages)
Network switches APC UTS6BI User Manual
(24 pages)
(24 pages)
Network switches APC AP7922 User Manual
(1 pages)
(1 pages)
Network switches APC H15 Service Manual
(86 pages)
(86 pages)
Network switches APC AP5616 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.843 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals