APC RAID Subsystem SCSI-SATA II User Manual Page 143
- Page / 259
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SAS / SATA II NAS System
User’s Manual
143
Network Adapter:
The Network Adapter section consists of the Adapter List and the Configuration section.
The Adapter List is the list of available Ethernet ports in the system. The number of ports
might be two or three depending on different models.
Adapter List: Lists the available Ethernet adapters.
Configuration:
Use Dynamic IP Configuration (BOOTP/DHCP) - If checked, this specifies
that this network connection will dynamically obtain an IP address from a
Dynamic Host Configuration Protocol (DHCP) server or from a Bootstrap Protocol
(BOOTP) server.
Enable this adapter on boot – If enabled, this adapter will be active when
proNAS starts up.
Enable default gateway on this adapter - If checked, the default gateway will
be enabled in this adapter. A default gateway is a local IP router that is used to
forward packets to destination beyond the local network. Only one default
gateway can be enabled in a certain time.
Device - Displays the type of Network Interface Card.
IP address – Shows the current IP address. To edit IP address, enter the new IP
address.
Gateway – Shows the current gateway IP address. To edit, type in a new
gateway IP address.
Subnet mask – Shows the current subnet mask setting. To edit, type in the new
subnet mask number.
MTU – The MTU size (Maximum Transmission Unit) in bytes. To modify the MTU
size for this interface, enter the new MTU size.
Network Trunking
ProNAS provides the network trunking/bonding function. Ethernet bonding refers to
aggregating multiple Ethernet channels together to form a single channel.
NOTE: It is necessary that the network switch supports the type of
trunking mode that will be used. Otherwise, the network
connections may become unstable.
- SAS/SATA II NAS System 1
- Table of Contents 2
- Preface 7
- FCC Compliance Statement 8
- Before You Begin 9
- SAS / SATA II NAS System 10
- User’s Manual 10
- Chapter 1 Introduction 11
- 1.1 Key Features 12
- 1.3 RAID Concepts 16
- RAID Management 20
- 1.4 Array Definition 21
- 1.5 High Availability 22
- 3.2 Powering On 28
- 3.3 Installing Hard Drives 30
- Main Menu 37
- Chapter 5 RAID Management 47
- 5.2 RAID Set Functions 49
- 5.2.2 Delete RAID Set 50
- 5.2.4 Offline RAID Set 54
- 5.2.6 Create Hot Spare 57
- 5.2.7 Delete Hot Spare 57
- 5.2.8 Rescue Raid Set 58
- 5.3 Volume Set Function 59
- 5.3.2 Create Raid 30/50/60 62
- 5.3.3 Delete Volume Set 63
- 5.3.4 Modify Volume Set 64
- 5.3.5 Check Volume Set 67
- 5.3.7 Stop Volume Check 70
- 5.4 Physical Drive 71
- 5.4.4 Identify Enclosure 73
- 5.5 System Controls 75
- 5.5.4 SNMP Configuration 79
- 5.5.5 NTP Configuration 80
- 5.6 Information Menu 84
- 5.6.2 System Information 85
- 5.6.3 Hardware Monitor 86
- PART II proNAS System 95
- Chapter 7 Introduction 96
- Chapter 8 proNAS Manager 104
- 8.1 Volume Manager 105
- 8.1.3 Volume Snapshot 118
- 8.1.3.3 Delete Snapshots 124
- 8.1.4 Volume Replication 126
- 8.1.5 iSCSI 134
- 8.2 Network Manager 142
- 8.2.2 Internet Gateway 146
- 8.2.3 SNMP/MRTG 147
- 8.2.4 Network Test 148
- 8.3 Account Manager 149
- 8.3.1.3 NIS Authentication 152
- 8.4 Share Manager 161
- 8.4.1 Share Management 162
- 8.4.1.2 Applying ACL 163
- 8.4.1.3 Modifying a Share 163
- 8.4.1.4 Deleting a Share 164
- 8.4.3 Protocol Setting 167
- 8.4.3.2 NFS 168
- 8.4.4.1 Group 169
- 8.4.4.2 Account 170
- 8.4.4.3 IP Address 172
- 8.4.6 Duplication 179
- 8.4.7 Default Share 183
- 8.5 System Manager 184
- 8.5.3 Report tab 187
- 8.5.4 Time tab 188
- 8.5.5 Serial Ports tab 189
- 8.5.6 Power tab 190
- 8.5.7 Reboot tab 191
- 8.5.8 Service tab 192
- 8.5.9 Status tab 195
- 8.6 Backup Manager 197
- 8.6.3 Tape Control 204
- 7. Click “Save” again 207
- 8.7 Log Manager 221
- 8.8 Event Manager 222
- Event Purpose 223
- Chapter 9 File Manager 225
- 9.2 Logon to File Manager 227
- Chapter 10 proBackup 231
- 10.3 Create Backup Plan 234
- 10.4 Restore Backup 240
- 10.5 Account Detail 241
- 11.3 ProNAS HA Properties 254
- 11.6 License Registration 258
- 11.7 Event Log Properties 259
Related products and manuals for Networking APC RAID Subsystem SCSI-SATA II
Networking APC Metered Rack User's Guide
(110 pages)
(110 pages)
Networking APC WMR1000B User Manual
(318 pages)
(318 pages)
Networking APC AP9606 User's Guide
(84 pages)
(84 pages)
Networking APC AP9613 Installation Manual
(36 pages)
(36 pages)
Networking APC AP9470 Installation Manual
(32 pages)
(32 pages)
Networking APC AP9622 Installation Manual
(28 pages)
(28 pages)
Networking APC IP DSLAM User's Guide
(603 pages)
(603 pages)
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.499 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals