APC RAID Subsystem SCSI-SATA II Specifications Page 27
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Step 5. Install the drive trays into the enclosure. Note that the drive trays
used in single- or redundant-controller subsystems are different. (See
Section 0)
Step 6. Connect the cables. Use the supplied power cords to connect the
subsystem to main power. It is recommended to connect power cords
to separate and independent power sources for higher redundancy.
Make sure your subsystem is electrically grounded.
It is also recommended to use the included cable clamps to prevent
accidental disconnection of the power cords. Use separately
purchased SCSI cables to connect the host ports to the host computers
or expansion enclosures. (See Chapter 4)
Step 7. BBU installation. Install the optional BBU module if it is included in
your order.
Step 8. Power up. Once all of the components have been properly installed
and all the cables properly connected, the subsystem can be powered
up and the RAID array configured. (See Chapter 4)
2.4.1 Installation Procedure Flowchart
Figure 2-1 shows a flowchart of the installation procedure. As you complete each step,
check off the “Done” box on the right. Please use this flowchart in conjunction with the
instructions that follow.
General Installation Procedure
2-3
- Falcon 24 Bay 1
- Table of Contents 2
- Safety Precautions 6
- About This Manual 7
- Revision History 7
- Who should read this manual? 7
- Conventions 8
- Software and Firmware Updates 9
- Chapter 1 10
- Introduction 10
- 1.1.2 Enclosure Chassis 11
- 1.1.2.1 Chassis Overview 11
- CAUTION! 12
- 1.1.2.2 Physical Dimensions 12
- 1.1.2.3 Front Panel Overview 13
- 1.1.2.4 Drive Slot Numbering 14
- 1.1.2.5 Rear Panel Overview 14
- 1.2. Subsystem Components 15
- 1.2.2 Drive Trays 16
- WARNING! 16
- 1.2.3 RAID Controller Module 17
- 1.2.5 DIMM Module 18
- 1.2.6 BBU Module 19
- 1.2.7 Power Supply Units 20
- 1.2.8 Cooling Modules 21
- 1.3. Subsystem Monitoring 22
- 1.4. Hot-swappable Components 23
- 1.4.3 Normalized Airflow 24
- Chapter 2 25
- Hardware Installation 25
- 2.3. Static-free Installation 26
- 2.5. Unpacking the Subsystem 28
- Considerations: 29
- WARNING! 30
- 2.7. Hard Drive Installation 34
- 2.8. Drive Tray Installation 35
- Chapter 3 43
- Subsystem Monitoring 43
- 3.2. Status-indicating LEDs 44
- 3.2.2 Controller Module LEDs 45
- 3.2.3 LAN Port LEDs 46
- 3.2.4 LCD Keypad Panel 46
- 3.2.5 Drive Tray LEDs 48
- 3.2.7 PSU Module LED 49
- 3.3. Audible Alarm 50
- C Monitoring 51
- Subsystem Connection and 52
- Operation 52
- 4.1.3 SCSI Termination 53
- 4-5: LCD Keypad Navigation 55
- 4.2 Connection Topology 57
- 4.3 Power On 61
- 4.3.2 Power On Procedure 62
- 4.3.4 Power On Status Check 63
- 4.3.5 LCD Screen 64
- 4.4 Power Off Procedure 65
- Chapter 5 66
- Subsystem Maintenance and 66
- Upgrading 66
- 5.2.1 Overview 68
- CAUTION! 73
- 5.4.2 Replacing a PSU Module 76
- 5.6. Drive Tray Maintenance 79
- 5.6.2 Hard Drive Replacement 80
- Appendix 81
- Subsystem Specifications 81
- A.2.1 Configuration 83
- A.2.2 Architecture 83
- A.6. RAID Management 85
- Appendix B 86
- Uninterruptible Power Supply 86
- B.4.2 Set the Baud Rate 87
- B.4.3 Connect COM2 87
- B.5. Power On 88
- B.6. UPS Status Monitoring 88
- B.6.2 UPS Messages 89
- B.6.3 UPS Message Summary 90
- Appendix C 91
- Spare Parts and Accessories 91
- Appendix D 93
- D.2. DB9 Audio Jack Pinouts 94
- Definitions 95
- D.3. Ethernet Port Pinouts 96
- D.4. Main Power 96
- Index I--1 97
- -2 Index 98
- Index I--3 99
- -4 Index 100
Related products and manuals for Networking APC RAID Subsystem SCSI-SATA II
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 1.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals