APC AP9630 User's Guide Page 59
- Page / 85
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
57UPS Network Management Card 2 User’s Guide
Tests menu
Testing and calibrating
Path: Tests > UPS
This option is not available for all UPS devices.
With some UPS devices, you can run a self-test, an alarm test, or a runtime calibration for your UPS. The Self-
Test and Calibration fields display the results of the most recent test and calibration.
A runtime calibration causes the UPS to recalculate its available runtime capacity based on its current load.
This ensures that the runtime reported is more accurate. Because a calibration temporarily depletes the UPS
batteries, you can perform a calibration only if battery capacity is at 100%. The load on your UPS must be at
least 15% without fluctuating to guarantee that a calibration will be accepted.
Caution - Runtime calibrations deeply discharge UPS batteries, which can leave a UPS temporarily
unable to support its equipment if a power outage occurs.
Frequent calibrations reduce the life of batteries.
Perform a calibration whenever you significantly increase the load that the UPS is supporting.
The alarm test for a UPS is device-specific and might not be available for your UPS. To enable the alarm, see
“UPS General screen”.
• When you select UPS Alarm Test, the UPS beeps for four seconds and the LEDs illuminate.
• When you select UPS Alarm Test - Continuous, the UPS beeps and illuminates the LEDs until you
cancel the test. A separate bullet displays on this screen, Cancel Continuous Alarm Test. To cancel
the test, select this and click Apply. Alternatively you press any key on the LED display interface of the
UPS. This test is useful for locating a UPS.
Setting the NMC LED lights to blink
Path: Tests > Network > LED Blink
If you are having trouble finding your UPS device, enter a number of minutes in the LED Blink Duration
field, click Apply, and your NMC LED lights will start flashing. This can assist in locating the physical device.
- User’s Guide 1
- ロードできます。 2
- 동봉된 CD 안에 한국어 매뉴얼이 있습니다 2
- Introduction 3
- IPv4 initial setup 4
- IPv6 initial setup 4
- Internal Management Features 5
- Front Panel (AP9630) 7
- Front Panel (AP9631) 7
- LED Descriptions 8
- Watchdog Features 9
- Web User Interface 10
- URL format examples 11
- Home Screen 12
- UPS on Status menu 13
- Field Description 14
- Outlet Groups on Status menu 15
- Universal I/O on Status menu 15
- Network on Status menu 15
- Controlling UPS and Security 16
- Action Description 17
- Outlet Groups on Control menu 19
- Security on Control menu 20
- Network on Control menu 21
- Configuring your Settings: 1 22
- Field Description 25
- UPS General screen 27
- Self-Test Schedule screen 28
- Shutdown Scheduling 28
- Firmware Update screen 29
- ftp> quit 30
- 221 Goodbye 30
- Third Party Support screen 32
- Universal I/O screens 33
- Input Contacts screen 34
- Output Relay screen 34
- Security menu 36
- Remote Users authentication 37
- RADIUS screen 38
- Configuring the RADIUS Server 38
- Firewall screen 39
- Configuring your Settings: 2 40
- Option Description 41
- DHCP response options 42
- address of the primary DNS 43
- Testing DNS screen 44
- Web access screen 44
- Web SSL Certificate screen 45
- Console screen 45
- SNMP screens 46
- SNMPv3 47
- FTP Server screen 48
- Notification menu 49
- E-mail notification screens 51
- SNMP Trap Receivers screen 53
- SNMP Traps test screen 54
- Remote Monitoring Service 54
- General menu 55
- Configure Links screen 56
- Logs on Configuration menu 57
- Tests menu 59
- Logs and About menus 60
- Data log 61
- Path: Logs > UPS 63
- Energy Usage 64
- Firewall Log 64
- About the UPS device 65
- Support screen 66
- System requirements 67
- Installation 67
- Summary of the procedure 68
- Contents of the .ini file 68
- Detailed procedures 68
- Messages in config.ini 70
- Related Topics 71
- File Transfers 72
- NMC over the network: 73
- NMC, see “FTP Server” 73
- C:\>cd apc 73
- C:\apc>dir 73
- Use XMODEM to upgrade one NMC 74
- NMC firmware: 75
- iplist.txt file 76
- Verifying Upgrades 77
- Troubleshooting 79
- SNMP Issues 80
- Synchronization Problems 80
- Two-Year Factory Warranty 81
- Warranty claims 82
- Radio Frequency Interference 83
- Australia and New Zealand 84
- European Union 84
- Korean 한국 84
- 990-3402E-001 85
Related products and manuals for Networking APC AP9630
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
Networking APC ADSL 4-Port User Manual
(13 pages)
(13 pages)
Networking APC 2200VA User Manual
(6 pages)
(6 pages)
Networking APC AP9622 User Manual
(4 pages)
(4 pages)
Networking APC AP9630 User's Guide
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.786 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals