APC IP DSLAM User's Guide Page 337
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
329
mgmtsvlanid
This parameter specifies the S-VLAN for
management traffic on this interface. It is
applicable only in stacked-VLAN Mode. Non-
zero value of this field is valid only if either
'etherIfIpAddress' field is non-zero or
'etherUseDhcp' field is true. If no management
S-Vlan id is specified (in the create operation) or
its value is set to zero (either in create or modify
operation), then the system shall use the value
of 'psvlanid' associated with the bridge port
created on this interface as the management
VLAN id. In case the management VLAN (virtual
VLAN mapped to S-VLAN and C-VLAN for the
frame) does not exist (ie. Virtual VLAN mapped
to 'mgmtsvlanid' or the associated 'psvlanid', if
'mgmtsvlanid' is zero) on the system, then IP-
based management shall not happen on the
interface till the corresponding virtual-VLAN is
created with the Net-side port as its member.
Type : Create - optional
Modify - optional
Valid values: 0 - 4095
m2vmacdbid
This field specifies the M2VMac Database Id
associated with this interface. The value 0
means Virtual MAC feature is disabled on this
interface. This field can be modified only when
the interface is disabled.
Type: Create - optional
Modify - optional
Valid values: 1 -
GS_CFG_MAX_M2VMAC_DATABASES
mgmttvlanid
<mgmttvlanid-val>
This specifies the value to be used for inserting
TVLAN id or vlan id of the third Vlan tag in the
transmitted Ethernet frames and that is expected
in received frames over this interface. Currently
this is configurable and supported only for
management Ethernet interface. For data
Ethernet interface, the value of TVLAN id is
configurable and used from the system sizing
table. If the value for TVLAN id configured on a
management Ethernet interface is zero then
third vlan tag shall not be added neither shall it
be supported in received frames. This attribute is
applicable only in stacked-VLAN mode.
Type: Create -- Optional
Modify -- Optional
Valid values: 0 - 4095
Default value: 0
Example
create ethernet intf ifname eth-0 ip 192.168.1.1 mask 255.255.255.0
speed 100bt profilename sprofile mgmtvlanid 2 priority 2
trfclassprofileid 1 Ctlpktinstid 1 ctlpktgroupid 1
Output
Verbose Mode On
Entry Created
Interface : eth-0
Type : Uplink UseDhcp : False
IP Address : 192.168.1.1 Mask :
255.255.0.0
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals