APC IP DSLAM User's Guide Page 409
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
401
this priority value, the subrule is created in fast
or
slow memory. In case priority is specified as
'asinrule', subrule priority will be same as
specified in the
rule.
Transport Header
This specifies the type of the transport header in
the packet in which the corresponding IP is
being transported. If the value of this field is
ethernet, then the IP is being carried in the
ethernet header. If it is ‘pppoe’, then the
corresponding IP is being carried in the PPP
header.
References
• Generic Filter commands
8.13.32 Filter subrule IGMP Commands
8.13.32.1 Get filter subrule igmp
Description: Use this command to get.
Command Syntax: get filter subrule igmp [ruleid <ruleid-val>]
[subruleid <subruleid-val>]
8.13.32.2 Create filter subrule igmp
Description: Use this command to create.
Command Syntax: create filter subrule igmp ruleid <ruleid-
val>subruleid <subruleid-val> [ igmptype <igmptype-val> ]
[ igmpcode <igmpcode-val> ] [ groupaddrfrom <groupaddrfrom-val> ]
[ groupaddrto <groupaddrto-val> ] [ igmptypecmp eq | neq | any ]
[ igmpcodecmp eq | neq | any ] [ igmpgroupaddrcmp eq | neq | lt |
leq | gt | geq | any | inrange | exrange ] [ subruleprio low | high |
asinrule] [ transporthdr ethernet | pppoe ]
8.13.32.3 Delete filter subrule igmp
Description: Use this command to delete.
Command Syntax: get filter subrule igmp ruleid <ruleid-
val>subruleid <subruleid-val>
8.13.32.4 Modify filter subrule igmp
Description: Use this command to modify.
Command Syntax: modify filter subrule igmp ruleid <ruleid-
val>subruleid <subruleid-val> [ igmptype <igmptype-val> ]
[ igmpcode <igmpcode-val> ] [ groupaddrfrom <groupaddrfrom-val> ]
[ groupaddrto <groupaddrto-val> ] [ igmptypecmp eq | neq | any ]
[ igmpcodecmp eq | neq | any ] [ igmpgroupaddrcmp eq | neq | lt |
leq | gt | geq | any | inrange | exrange ] [ subruleprio low | high |
asinrule] [ transporthdr ethernet | pppoe ]
Parameter
Name Description
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.297 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals