APC AP7602 Instruction Manual Page 47
- Page / 294
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
The InfraStruXure Central Console
46 InfraStruXure Central 4.0 User’s Reference
The Action/Information Pane
Located on the right-hand side of the interface, the Action/Information pane contains a series of buttons
that enable you to view information and perform mass configuration tasks on the devices in the currently
selected device group, or the devices that are currently selected in the Device Selection pane. Each
button, when selected, presents a different view in the Action/Information pane. The Action/Information
pane features 6 buttons:
Action Pane View Description
Map View All devices in the selected device group are displayed as icons.
Current reading reported by a selected sensor is displayed for
each device. The default sensor that is currently selected is
shown above the Map View in the center of the Action/
Information pane. Current status can also be indicated with
sensor imaging. If you select one or more devices from the
Device Selection pane, the icons for the selected devices are
selected in the Map view as well.
Table View Data about all devices in the selected device group are displayed
in a table. Problems, such as device outages or alert conditions
are indicated by a user-defined color (red by default) in the
appropriate field. If you select one or more devices from the
Device Selection pane the entries for the selected devices in the
Table view are selected as well.
Alert View Enables you to easily view all alerts that have been generated by
NetBotz devices in the currently selected device group. Alerts
that contain picture data can also be viewed from this pane if the
alerts are posted to the
InfraStruXure Central server using
HTTP Post support (for more information, see “Creating a Send
HTTP Post Alert Action” on page 235). If you select one or
more devices from the Device Selection pane any devices from
the device group to which the selected devices belong that have
reported alerts on the date selected in the Alerts view will be
listed in the Alerts view. If a device appears in the Alerts view
but cannot be selected (and is “grayed out”) then no alerts have
been posted to or collected from the selected device on the
selected date.
Graph/Report View Data about one or more selected sensors, for a user-specified
time period, is collated and then either plotted in a color-coded
line graph or used to generate a report. Data about multiple
devices can be graphed in a single graph view to simplify data
collation and comparison.
Mass Configuration Provides complete mass device configuration functionality,
enabling you to perform all of the tasks necessary for complete
management of all of your devices, one at a time or all at once.
The Mass Configuration panel is divided into two areas: Sensor
& Alerts Settings and Host Device Settings. Each area features a
number of icons that represent the mass configuration tasks that
you can perform.
- User’s Reference 1
- Contents 4
- Introduction 12
- About the Installer CD 14
- Installing on a Linux System 15
- Installation Instructions 20
- Before You Begin 20
- RapidRails Rack Kit Contents 21
- Installation Tasks 22
- Replacing the Rack Doors 28
- Getting Started 30
- The Group Navigation Pane 32
- The Device Selection Pane 32
- The Action/Information Pane 33
- Predefined Groups 34
- Discovering Your Devices 36
- Creating Device Groups 37
- Creating User Accounts 39
- Interface Navigation 46
- Predefined Device Groups 48
- Map View 48
- Table View 52
- Alert View 53
- Graph/Report View 55
- Mass Configuration View 57
- About Deleting Devices 57
- Using Filters 58
- Configuring Color Preferences 63
- Messages 68
- Server Administration 68
- Server Control 69
- Server Messages 69
- Server Administration Tasks 72
- Server Backup 73
- Server Restore 74
- The Monitor Settings Pane 77
- Device Group Administration 78
- Discovery Settings 81
- Running Discovery Processes 84
- DHCP LAN Discovery 84
- Disk Array Management 85
- Export Administration 85
- Install/Upgrade Management 88
- Look and Feel 89
- Management Device Job Control 89
- Using the Job Status Pane 90
- Using the Job Settings Pane 90
- Server Settings 93
- Network Settings 94
- E-mail Settings 95
- Log Settings 97
- Time Settings 98
- Server Access 99
- SOCKS Proxy Pane 100
- Server Security 101
- Storage Repositories 102
- The Storage Settings Pane 103
- The Repositories Pane 104
- Surveillance Administration 105
- User/Group Administration 105
- Field Description 106
- Creating and Editing Groups 108
- Adding New Devices 110
- Settings 112
- Alert Actions 114
- Creating Alert Actions 115
- Alert Profile 116
- Creating an Alert Sequence 117
- Creating an Alert Profile 118
- Periodic Reports 119
- Field Description 122
- FTP reports. The settings 126
- State Sensors and Thresholds 132
- Defining Numeric Thresholds 132
- Minimum Value Threshold 134
- Range Threshold 136
- Rate of Decrease Threshold 143
- Rate of Increase Threshold 146
- Defining State Thresholds 148
- State Mismatch Threshold 152
- Configuring Offline Devices 158
- About Information 158
- Monitored Device Settings 159
- Camera Configuration 160
- Control Description 161
- Camera Masking 164
- The Block Out Mask Tab 165
- Custom Audio Clips 167
- Device Crawlers 168
- OID-Specific Monitoring 170
- Enhanced Alert Notification 170
- The Supplemental OIDs Pane 175
- Device Scanner 176
- E-mail Server 182
- External Ports 184
- External Storage 188
- Using a Windows Share 189
- Using an NFS Mount 190
- Remote hostname/IP 190
- Remote share name 190
- IP Filter 191
- IPMI Devices 192
- License Keys 194
- Location 195
- Network Interfaces 199
- Network Interface window: 200
- Pod Sharing 204
- Remote Devices list 205
- PPP/Modem 206
- Using SIM Security 209
- Upgrading Devices Over PPP 209
- Root Password 212
- Serial Devices 213
- Upgrade 218
- Privilege Set Description 219
- View Device Logs 220
- Web Server 220
- Example Target URLs 229
- BotzWare macros 231
- Using the Map View 246
- Editing Map Settings 249
- Using Sensor Imaging 250
- Map Sharing 251
- Using the Table View 252
- Using the Alert View 254
- ) button 255
- Using the Graph/Report View 256
- Surveillance View 262
- Enabling Surveillance 264
- About the Surveillance View 268
- Two-Way Audio Functionality 269
- Using the Clip View Pane 270
- Generating Clips 271
- Tagging Clips 272
- Disabled 277
- Send Continuous During Alerts 277
- Send on Motion Detected 278
- BotzWare Macros 280
- Macro Definition Example 281
- Alert Macros 282
- Troubleshooting 284
- Macro Example String 285
- Example Session 287
- Basic Network Troubleshooting 289
- Warranty and Service 290
- Life-Support Policy 292
Related products and manuals for Power supply units APC AP7602
Power supply units APC AP9341 User Manual
(24 pages)
(24 pages)
Power supply units APC S20BLK User Manual
(20 pages)
(20 pages)
Power supply units APC 990-2233A User Manual
(19 pages)
(19 pages)
Power supply units APC 208 VAC User Manual
(11 pages)
(11 pages)
Power supply units APC AP9621 Specifications
(24 pages)
(24 pages)
Power supply units APC LX User Manual
(2 pages)
(2 pages)
Power supply units APC 5000I User Manual
(23 pages)
(23 pages)
Power supply units APC SYPM2KU User Manual
(22 pages)
(22 pages)
Power supply units APC AP9215 Specifications
(24 pages)
(24 pages)
(34 pages)© 2020, manymanuals.com. All rights reserved. | 0.868 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals