APC IP DSLAM User's Guide download pdf (Page 544)

536

value is ignored. Type: Modify － Optional

Valid values: 1 -175

mcastcap ivmcapable

|svmcapable | none

It denotes the Multicast Device Capability. If the

device capability is ivlcapable then svmcapable

is not a valid value. If the device capability is

neither ivlcapable nor svmcapable then the only

valid value for this field is none. If the device

capability is ivlcapable or svlcapable then this

field can't have value none. ivmcapable and

svmcapable can't be set together.In case of

Stacked Vlan Mode this shall apply to Virtual

Vlans.

Type: Modify － Optional

ridcap irdcapable

|srdcapable

RID refers to the Routing Information Database.

This database contains information about the

routes in the system. Each RID identifies a flow

and defines route related information for that

flow. The RID defines a flow based on the VLAN

Id. The database can be of 2 types,

IRD( Independent Routing Database) where

there are more than one RIDs in the system and

each RID defines separate routes in context of

itself. If VlanId <X> and RID <X> have been

created and the routing database is configured

for IRD, than routes in RID <X> shall define flow

for packets coming on VLAN Id <X>. The other

mode for the database is SRD( Shared Routing

Database) where there is a single RID in the

system and all flows map to this RID. This RID

has to be explicitly created and no more than 1

RID can be created in the system in this mode.

Flows for all created VLANs shall map to this

RID for routing.

Type: Modify － Optional

maxnumac <maxnumac-

val>

It denotes the maximum number of Access

Concentrators supported.

Type: Modify － Optional

Valid values: 1 - 8

maxnumsrcmac

<maxnumsrcmac-val>

It denotes the maximum number of Source MAC

addresses that can be used across the different

PPPOE and IPOE interfaces.

Type: Modify － Optional

Valid values: 1 - 8

vlanmode nativemode

|stackedmode

Vlan Mode Type: Modify Optional

svlanprotocolid

<svlanprotocolid-val>

This specifies the ProtocolId value to be used for

Stacked Vlan/Service Vlan/Provider

Vlan/Second Vlan tag. It is recommended to

keep the value for this different from ProtocolId

value defined for 802.1q Vlan(0x8100). This

attribute is applicable only in 'VLAN Stacking

mode'.

Type: Modify － Optional

Valid values: 0x8100 -

0xFFFF

tvlanprotocolid

<tvlanprotocolid-val>

This specifies the ProtocolId value to be used for

Stacked Vlan/Service Vlan/Provider

Vlan/Second Vlan tag. It is recommended to

keep the value for this different from ProtocolId

value defined for 802.1q Vlan (0x8100). This

attribute is applicable only in 'VLAN Stacking

mode'.

Type: Modify － Optional

Valid values: 0x8100 －

0xFFFF

tvlanid <tvlanid-val>

This specifies the ProtocolId value to be used for

Stacked Vlan/Service Vlan/Provider

Vlan/Second Vlan tag. It is recommended to

keep the value for this different from ProtocolId

value defined for 802.1q Vlan(0x8100). This

attribute is applicable only in 'VLAN Stacking

1 2 ... 539 540 541 542 543 544 545 546 547 548 549 ... 602 603

Comments to this Manuals

No comments

APC IP DSLAM User's Guide Page 544

Comments to this Manuals

Related products and manuals for Networking APC IP DSLAM