APC IP DSLAM User's Guide Page 214
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
206
Set Done
Output Fields
Field Description
Port Id
The port number of the port for which this entry
contains Spanning Tree Protocol management
information.
Priority
The value of the priority field which is
contained in the most significant 6 bits of the
more significant octet of the (2 octet long) Port
ID. The least significant 2 bits of the more
significant octet and the less significant octet
(total 10 bits) of the Port ID is given by the
value of dot1dStpPort.
State
The port's current state as defined by
application of the Spanning Tree Protocol.
This state controls what action a port takes on
reception of a frame.
Port Status
The enabled/disabled status of the port.
Path Cost
The contribution of this port to the path cost of
paths towards the spanning tree root which
include this port.
Desig Cost
The path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in
received bridge PDUs.
Desig Root
The unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration
BPDUs transmitted by the Designated Bridge
for the segment to which the port is attached.
Desig Bridge
The Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.
Desig Port
The Port Identifier of the port on the
Designated Bridge for this port's segment.
Fwd Transitions
The number of times this port has transitioned
from the Learning state to the Forwarding
state.
STP status
Spanning Tree Protocol to be enabled on the
Bridge or not.
STP PacketsPrio
For STP PDUs, this priority shall be used for
choice of traffic class/ Queue on out¦going
interface. In case the bridge port is over an
Aggregated ATM VC, this will also be used to
identify the VC, on which the packet is to be
sent
Caution
• The specified interface should be an existing bridge interface.
References
• bridge port intf command.
8.6.14 Transparent Bridging Table Commands
8.6.14.1 Modify bridge t/jointfilesconvert/324040/bg info
Description Use this command to modify.
Command Syntac: modify bridge t/jointfilesconvert/324040/bg info [aging <aging-timeout> ]
[slaveaging <aging-timeout> ] [netaging <aging-timeout> ]
[ floodsupport enable | disable ] [ bcastsupport enable | disable]
[ mcastsupport enable | disable ] [ mcastdrop enable | disable ]
[ dropiffdbfull <dropiffdbfull-val> ] [ resnetlearning <resnetlearning-
val> ] [resvmacprofileid <resvmacprofileid-val> ]
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.157 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals