APC IP DSLAM User's Guide Page 187
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
179
aal5
This specifies the AAL type in use for this VC. The
only type of AAL supported in Columbia Packet is
AAL5. This field is not valid for an ATM VC with
encaptype as Ethernet.
Type: Create Optional
Default value: aal5
a5txsize <aal5-cpcs-
txsdu-size >
This specifies the maximum transmit CPCS SDU
size to be used.
Type: Optional
Valid values : 1-1536
Default Value: 1536
a5rxsize <aal5-cpcs-
rxsdu-size>
This specifies the maximum receive CPCS SDU
size to be used
Type: Optional
Valid values : 1-1536
Default Value: 1536
vcmux|llcmux|auto|
ethernet
This specifies the data encapsulation method to
be used over the AAL5 SSCS layer. "auto" means
autosense the muxType(llc/vc). Auto mode is only
used to sense the llc/vcmux. Atm VC with
encaptype as ethernet can be created only over
an ATM port which has value of atmtransporttype
as packet.The VPI/VCI values for this atm vc shall
be 0/0. aaltype, mgmtmode and oam related
parameters are not valid for an ATM VC with
encaptype as Ethernet.
Type: Optional
Default Value: llcmux
Pvc
This specifies the type of VC. The only value
supported is PVC.
Type: Optional
Default Value: pvc
channel
fast|interleaved
This extension specifies the type of channel on
which the ATM VC's cells have to be transmitted/
received. This field is deprecated and currently
not in use.
Type: Optional
Default Value: Interleaved
Maxnumproto
<maxnumproto-val>
This field specifies the maximum number of
simultaneous active protocol stacks supported on
this interface. Currently, only one protocol stack is
supported.
Type: Create － Optional
Default value: 1
Autostatus
Enable|Disable
This field specifies whether the Auto mode is to be
enabled or not. In the Auto mode, the stack above
this interface will be determined and created
based on the protocol packets sensed on this
interface. For example, if the protocol packet
sensed above this interface is an EoA packet,
then the corresponding EoA stack will be created
above this interface. However, the corresponding
EoA interface must have been created with the
config status field set as config mode. This field is
not valid if encaptype is Ethernet.
Type: Create － Optional
Default value: disable
autosupportedprot
none|{pppoa | eoa |
ipoa}+
This field specifies Higher layer protocols which
are supported for auto detection on the given ATM
VC. Only the packets if the protocols mentioned in
this field can lead to Auto detection. This field is
meaningful only when autostatus flag as enable.
Type: Create － Optional
Modify － Optional
Default value: 1
autovcmuxforcedprot
None | pppoa | eoa |
ipoa
This field specifies that if the encap type detected
is VCMux, the user can configure to build a
specific protocol stack automatically. It can only be
present with the autostatus flag as enable. In case
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 1.383 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals