APC IP DSLAM User's Guide Page 215
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
207
8.6.14.2 Get bridge t/jointfilesconvert/324040/bg info
Description: Use this command to get bridging related global
information.
Command Syntax: get bridge t/jointfilesconvert/324040/bg info
Parameters
Name Description
Aging <aging-timeout>
The timeout period, in seconds, for aging out
dynamically learned forwarding information from
CPEs. The value 0 can be configured when aging
is to be stopped.
Type: Modify Optional
Valid values: 10 -1000000
slaveaging <aging–
timeout>
The timeout period, in seconds, for aging out
dynamically learned forwarding information
learned from the slave device. The recommended
value for this is more than or equal to the value for
dot1dTpAgingTimeOut. The value 0 can be
configured when aging is to be stopped.
Valid values: 10 -1000000
netaging <aging –
timeout>
The timeout period, in seconds, for aging out
dynamically learned forwarding information from
NET side port. This is used only for full bridge
configuration. The recommended value of net
aging timeout should be greater than that of the
ìAgingî parameter. The value 0 can be configured
when aging is to be stopped.
Valid values: 10 -1000000
floodsupport enable |
disable
This is used to specify whether the unknown
unicast packets are to be flooded or not. The
value for this is used along with per vlan
configuration for flood support to determine if
flooding has to be done for unknown unicast
packet.
Type : Optional
Valid Values: enable | disable
bcastsupport
enable|disable
This is used to specify whether the broadcasting is
supported or not. The value for this is used along
with per vlan configuration broadcast support, to
determine if broadcasting has to be done for the
broadcast packet.
mcastsupport
enable|disable
Used to specify whether the multicast is supported
or not.
Type : Optional
Valid Values: enable| disable
mcastdrop
enable|disable
Used to specify whether the multicast packets are
to be dropped, or to be forwarded, if multicast is
not supported. This is only valid if
dot1dTpMcastSupport is false.
Type : Optional
Valid Values: enable|disable
dropiffdbfull enable |
disable
This specifies if the frame for which learning could
not be done because of forwarding table limit
being reached, is to be dropped. If this is enabled
the frame for which learning could not be done
because of limit exceeded shall be dropped, else
forwarded based on bridge forwarding logic.This
being enabled shall reduce flooding, as when a
response to such a frame from which learning
could not be done shall come the frame shall be
flooded, as the entry for that unicast address, shall
not be found in forwarding table.
Type : Optional
Valid Values: enable or disable
Default value: enable
resnetlearning enable
| disable
This specifies if learning can be done over net
side port for residential bridging. Learning shall be
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals