APC IP DSLAM User's Guide Page 217
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
209
Field Description
MacAddress
The MAC address used by this bridge, when it
must be referred to, in a unique fashion. It is the
address of one of the Ethernet ports.
No. of Ports
The maximum number of ports that can be
controlled by this bridge.
Base Type
Indicates what type of bridging this bridge can
perform. It is always Transparent Bridging or
STP.
Aging TimeOut
The timeout period, in seconds, for aging out
dynamically learned forwarding information from
CPEs. The value 0 can be configured when
aging is to be stopped.
Slaveaging TimeOut
The timeout period, in seconds, for aging out
dynamically learned forwarding information
learned from the slave device. The
recommended value for this is more than or
equal to the value for dot1dTpAgingTimeOut.
The value 0 can be configured when aging is to
be stopped.
Floodsupport
This is used to specify whether the unknown
unicast packets are to be flooded or not. The
value for this is used along with per vlan
configuration for flood support to determine if
flooding has to be done for unknown unicast
packet.
Bcastsupport
This is used to specify whether the broadcasting
is supported or not. The value for this is used
along with per vlan configuration broadcast
support, to determine if broadcasting has to be
done for the broadcast packet.
Mcastsupport
Used to specify whether the multicast is
supported or not.
Mcastdrop
Used to specify whether the multicast packets
are to be dropped, or to be forwarded, if
multicast is not supported. This is only valid if
dot1dTpMcastSupport is false.
NetAgingTimeout
The timeout period, in seconds, for aging out
dynamically learned forwarding information from
NET side port. This is used only for full bridge
configuration. The recommended value of net
aging timeout should be greater than that of
dot1dTpAgingTimeOut.
Full Bridging Status
This specifies the current state of full bridging on
the bridge. Thebridge can be set to residential
bridging, restricted full bridging or unrestricted
full bridging. In residential bridging, all packets
from a CPE side port are sent to Net side port
without doing a lookup in the forwarding table. In
restricted full bridging, there is a lookup and a
packet coming from a CPE port destined for
another CPE port is dropped. Hence, CPE-CPE
switching is not permitted. In unrestricted full
bridging, all traffic is forwarded based on lookup.
Drop If FDB full status
This specifies if the frame for which learning
could not be done because of forwarding table
limit being reached, is to be dropped. If this is
enabled the frame for which learning could not
be done because of limit exceeded shall be
dropped, else forwarded based on bridge
forwarding logic.This being enabled shall reduce
flooding, as when a response to such a frame
from which learning could not be done shall
come the frame shall be flooded, as the entry for
that unicast address, shall not be found in
forwarding table.
ResidentialNetLearning
This specifies if learning can be done over net
side port for residential bridging. Learning shall
be done on Net port in case of vlan with
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals