APC IP DSLAM User's Guide Page 271
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
263
gsparamtestinputfile
<gsparamtestinputfile-
val>
Indicates Name of the Input file from which to take
the Mask Array Size, lower and upper mask Array.
Null string means no file is specified
Type: Modify -- Optional
atuctargetsnr
<atuctargetsnr-val>
Configured Target Signal/Noise Margin. This is the
Noise Margin the modem must achieve with a
BER of 10 to the power -7, or better, to
successfully complete initialization.
Type: Modify -- Optional
Valid values: 0 - 310
atucmaxsnrmargin
<atucmaxsnrmargin-
val>
Configured Maximum acceptable Signal/Noise
Margin. If the Noise Margin is above this, the
modem hould attempt to reduce its power output
to optimize its operation.
Type: Modify -- Optional
Valid values: 0 - 310
atucgsrsintcorrection
up 125us | 250us |
500us | 1ms | 2ms |
4ms | disable
Sets the correction time for the upstream
interleaved buffer. RS can also be disabled.
Type: Modify -- Optional
atucdnshiftsnrmargin
<atucdnshiftsnrmargin-
val>
Configured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the
modem should attempt to decrease its transmit
rate. In the case that RADSL mode is not present,
the value will be 0.
Type: Modify -- Optional
Valid values: 0 - 310
atucupshiftsnrmargin
<atucupshiftsnrmargin-
val>
Configured Signal/Noise Margin for rate upshift. If
the noise margin rises above this level, the
modem should attempt to increase its transmit
rate. In thecase that RADSL is not present, the
value will be 0.
Type: Modify -- Optional
Valid values: 0 - 310
atucminupshifttime
<atucminupshifttime-
val>
Minimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs. In the
case that RADSL is not present, the value will be
0.
Type: Modify -- Optional
Valid values: 0 - 16383
atucmindnshifttime
<atucmindnshifttime-
val>
Minimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs. In the
case that RADSL is not present, the value will be
0.
Type: Modify -- Optional
Valid values: 0 - 16383
atucfastmintxrate
<atucfastmintxrate-val>
Configured Minimum Transmit rate for 'Fast'
channels, in bps. Also refer to
'adslAtucConfRateChanRatio' for information
regarding RADSL mode and refer to ATU-R
transmit rate for ATU-C receive rates.
Type: Modify -- Optional
Valid values: 0 - 0xffffffff
atucintlmintxrate
<atucintlmintxrate-val>
Configured Minimum Transmit rate for 'Interleave'
channels, in bps. Also refer to
'adslAtucConfRateChanRatio' for information
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 2.103 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals