APC IP DSLAM User's Guide Page 276
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
268
Type: Modify -- Optional
upstreampsd
Extended | Standard |
Jj100
Conexant parameter that sets the upstream PSD
to be either extended or standard. Used for
GSpan Plus only.
Type: Modify -- Optional
atucconfpmmode
pmstatel3enable |
pmstatel2enable |
disable
PM-related parameter used by the ATU-C to set
the allowed link states. Both bit values can be
given simultaneously in the input. Additional value
to disable pmmode is disable, which is equal to 0.
Type: Modify -- Optional
atucconfpml0time
<atucconfpml0time-val>
PM configuration parameter, related to the L2 low
power state. This parameter represents the
minimum time (in seconds) between an exit from
the L2 state and the next entry into the L2 state. It
ranges from 0 to 255 seconds.
Type: Modify -- Optional
Valid values: 0 - 255
atucconfpml2time
<atucconfpml2time-val>
PM configuration parameter, related to the L2 low
power state. This parameter represents the
minimum time (in seconds) between an Entry into
the L2 state and the first Power Trim in the L2
state and between two consecutive Power Trims
in the L2 State. It ranges from 0 to 255 seconds.
Type: Modify -- Optional
Valid values: 0 - 255
atucconfpml2atpr
<atucconfpml2atpr-val>
PM configuration parameter, related to the L2 low
power state. This parameter represents the
maximum aggregate transmit power reduction (in
dB) that can be performed through a single Power
Trim in the L2 state. It ranges from 0 dB/10 to 310
dB/10.
Type: Modify -- Optional
Valid values: 0 - 310
atucconfpml2minrate
<atucconfpml2minrate-
val>
PM configuration parameter, related to the L2 low
power state. This parameter specifies the
minimum net data rate during the low power state
(L2). The data rate is coded in bit/s, and can range
from 0x1F40 (8000) bps to 0xFA000 (1024000)
bps.
Type: Modify -- Optional
Valid values: 0x1F40 - 0xFA000
atucconfmsgminds
<atucconfmsgminds-
val>
Configures downstream overhead channel
bandwidth. This feature is not supported by
DSLPHY as yet.
Type: Modify -- Optional
Valid values: 4000 - 64000
aturconfmsgminus
<aturconfmsgminus-
val>
Configures upstream overhead channel
bandwidth.This feature is not supported by
DSLPHY as yet.
Type: Modify -- Optional
Valid values: 4000 - 64000
atucminsnrmgn
<atucminsnrmgn-val>
Atuc Configured Minimum Signal/Noise Margin.
This is the Noise Margin, the modem must
achieve with a BER of 10 to the power -7 or better,
to successfully complete initialization. The default
value mentioned is an indicative value only.
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.297 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals