APC IP DSLAM User's Guide Page 575
- Page / 603
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
567
addresses are the multicast addresses
defined as reserved in IEEE 802.1Q and IEEE
802.1ad. The existence of the specified
"ResvdCtlPktProfile Table" entry is a must for
VLAN static entry creation to succeed.
Further, even if the specified
"ResvdCtlPktProfile Table" entry exists, but
the corresponding entry in "ResvdCtlPktProfile
Param Table" is missing the packets will be
dropped. VLAN here means the 802.1q Vlan
in case of Native Vlan mode and Virtual Vlan
in case of Stacked Vlan Mode.
Type: Create -- Optional
Modify -- Optional
Valid values: 1 - 4
Default value: 1
igmpsnoopaction Drop |
TransparentlyForward |
Learn
This parameter specifies that if an action is
"Learn" then igmpsnoop will be supported for
this Vlan and an entry will be learnt. Here
action will be applied in conjunction with
global igmpsnoopStatus and port level
igmpsnoopStatus flags, that is IGMP
functionality will be executed for a frame if
IGMP is enabled globally and on the port it
has been received and for the vlan/virtual vlan
on which it has come.If action is "drop" then
igmpsnoop functionality is not supported for
this vlan and IGMP frames shall be dropped.
If action is "transparently forward", then IGMP
frames received for this Vlan shall be
forwarded transparently and learning will not
be done
Type: Create -- Optional
Modify -- Optional
Default value: Learn
igmpsnoopproxyreporting
Enable | Disable
This parameter provides a configuration
option to choose between transparent
snooping or Proxy reporting behavior per
Vlan. Depending on the type of mode, IGMP
module will perform either transparent
snooping or proxy reporting for the IGMP
messages, received on a Vlan. Here the Vlan
which is being referred is the one on which
learning will happen. It will be multicast vlan, if
"Multicast Vlan option" is enabled.
Type: Create -- Optional
Modify -- Optional
Default value: Disable
igmpsnoopingressprio
igmpsnoopingressprio |
none
This parameter specifies the ingress priority to
be forced on the incoming frame. If the
ingress priority field has valid value, then that
value will be used for traffic class
determination and packet priority. If valid
egress priority is configured for a port, then
egress priority shall override the ingress
priority. In addition, there is support of invalid
value for ingress priority to indicate that the
priority is not to be forced on ingress frame for
this port.Here the Vlan which is being referred
is the one on which learning shall happen. It
will be multicast vlan, if "Multicast Vlan option"
is enabled.
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Related products and manuals for Networking APC IP DSLAM
Networking APC AP9606 Quick Start Manual
(20 pages)
(20 pages)
Networking APC AP9312TH User's Guide
(32 pages)
(32 pages)
Networking APC AP9608 Installation Manual
(32 pages)
(32 pages)
Networking APC 66123 Installation Manual
(16 pages)
(16 pages)
Networking APC AP9630 User's Guide
(85 pages)
(85 pages)
Networking APC IP DSLAM User's Guide
(67 pages)
(67 pages)
Networking APC AP9630 User Manual
(117 pages)
(117 pages)
Networking APC AP9630 User Manual
(32 pages)
(32 pages)
Networking APC AP9224110 Specifications
(16 pages)
(16 pages)
Networking APC AP9608 Specifications
(9 pages)
(9 pages)
Networking APC AP9608 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals