APC InfraStruXure Power Supply Specifications Page 63
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting: Alarm Messages on the Display Interface
InfraStruXure 20kW System: Installation, Operation, and Maintenance 57
Battery Module Quantity
decreased
At least one Battery Module has been
removed from the system.
If no Battery Modules have been
removed, ensure that all Battery Units
are properly inserted.
Power Module Quantity
increased
At least one Power Module has been
added to the system
No corrective action necessary.
Power Module Quantity
decreased
At least one Power Module has been
removed from the system.
If no Power Modules have been
removed, check that all Power
Modules are properly inserted, the
two fastening screws are tight, and
the locking latch is engaged.
Battery Cabinet Quantity
increased
At least one external battery cabinet
has been connected to the UPS.
No corrective action necessary.
Battery Cabinet Quantity
decreased
At least one external Battery
Enclosure has been disconnected
from the UPS.
Ensure that all Battery Enclosure
communication cables are properly
connected and that the LEDs are
illuminated on the battery
communication cards.
Low-Battery The UPS is online and the battery
charge is low.
No corrective action necessary. Note:
If the input voltage fails, runtime will
be limited.
Battery Discharged The UPS is in battery operation and
the battery charge is low.
No corrective action necessary. Note:
Runtime is limited in duration. Shut
down the system and the load
equipment or restore incoming
voltage.
Automatic Self Test
Started
The UPS has started pre-programmed
battery test.
No corrective action necessary.
Number of System
Power Supplies
Decreased
One of the system power supplies has
been removed.
If no system power supplies have
been removed, check that they have
been properly inserted.
External switch gear
Q001 closed
The external switch gear Q001 is
closed.
No corrective action necessary.
External switch gear
Q001 opened
The external switch gear Q001 is
open.
No corrective action necessary. The
UPS is disconnected from the input
power.
External switch gear
Q002 closed
The external switch gear Q002 is
closed.
No corrective action necessary.
External switch gear
Q002 opened
The external switch gear Q002 is
open.
No corrective action necessary. The
load is disconnected from the UPS
output.
External switch gear
Q003 closed
The external switch gear Q003 is
closed.
No corrective action necessary. The
UPS is in maintenance bypass
operation.
Display message Meaning Corrective action
- InfraStruXure 20kW System 1
- Contents 3
- Warnings 8
- Total power off procedure 9
- Batteries—CAUTION 9
- Emergency Power Off (EPO) 9
- Handling and transport 10
- Overview 11
- Front view (interior) 12
- Front view (lower interior) 13
- Rear view 14
- Main input connection options 15
- Site Planning 17
- Electrical requirements 18
- Heat output 18
- Installation 19
- Ensure that all power is off 21
- Normally Open (NO) 25
- EPO Control 25
- Normally Closed (NC) 25
- System Start-Up 31
- Start-Up Procedure 32
- Top-Level Status Screen 34
- Top-Level Menu 34
- Control Menu 34
- Apply power to load equipment 35
- Quick Configuration 37
- Interface 38
- APC Management Card Wizard 39
- 01) is the code 41
- 04) is the length 41
- Control Console 42
- IP address. For example: 43
- 20kW System 44
- Operation 45
- Navigating screens 46
- Top-Level Status screen 47
- Top-Level Menu screen 47
- Control screen 48
- Status screens 48
- Setup screen 49
- Accessories screen 50
- NTER key to view a 51
- NTER key. Then press the 52
- Procedures 53
- Operation: Procedures 54
- DC Disconnect breaker to OFF 55
- 6. Turn OFF the Q1 switch 55
- How to ensure total power off 59
- Troubleshooting 61
- General status 62
- General fault 64
- Check that all power mod 65
- Module failure 66
- Threshold alarm 66
- Maintenance 69
- How to return parts to APC 70
- Replacement parts 70
- How to remove a power module 71
- How to install a power module 72
- How to remove a card 73
- How to install a card 73
- Battery replacement 74
- Adding Parts 75
- Add a circuit breaker 76
- Add a power cable 77
- Maintenance: Adding Parts 78
- Upgrading Firmware 79
- Specifications 81
- Product Information 87
- APC three-phase systems 88
- Obtaining service 89
- *990-1493* 92
Related products and manuals for Power supply units APC InfraStruXure Power Supply
Power supply units APC 208 VAC User Manual
(10 pages)
(10 pages)
Power supply units APC BX1300G User Manual
(20 pages)
(20 pages)
(15 pages)
Power supply units APC AP7622 User Manual
(28 pages)
(28 pages)
Power supply units APC 208 VAC User Manual
(25 pages)
(25 pages)
(30 pages)
Power supply units APC 10-30 KVA User Manual
(32 pages)
(32 pages)
Power supply units APC AP7820 User Manual
(12 pages)
(12 pages)
Power supply units APC S15 Specifications
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 0.411 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals